Description: This code was used for making the practical measurements in section 2.3 of my thesis. This Matlab code allows an OFDM signal to be generated based on an input data file. The data can be random data, a grey scale image, a wave file, or any type of file. The generated OFDM signal is stored as a windows wave file, allowing it to be viewed, listened to and manipulated in other programs. The modified wave file can then be decoded by the receiver software to extract the original data. This code was developed for the experiments that I performed in my honours thesis, and thus has not been fully debugged.
This is the original code developed for the thesis and so has several problems with it. The BER performance given by the simulations is infact Symbol Error Rate.
-This code was used for making the practical measurements in section 2.3 of my thesis. This M atlab code allows an OFDM signal to be generated based on an input data file. The data can be rando m data, a gray scale image, a wave file, or any type of file. The OFDM signal is generated stored as a windows wave file, allowing it to be viewed. listened to and manipulated in other programs. The modified wave file can then be decoded by the receiver software to extract the original data . This code was developed for the experiments th at I performed in my honors thesis, and thus has not been fully debugged. This is the original code developed for the thesis and so ha 's several problems with it. The BER performance given by the simulations is infact Symbol Error Rate. Platform: |
Size: 161792 |
Author:王文 |
Hits:
Description: 通信系统中常用的多进制数字相位调制的源代码 并结合ofdm系统 加入了相应的保护前缀（cp）和导频序列 应用于有关ofdm的信道估计等系统-Communication systems commonly used in multi-band digital phase modulation of the source code and combine OFDM system by adding a prefix corresponding protection (cp) and the pilot sequence used in the relevant channel estimation of OFDM systems Platform: |
Size: 1024 |
Author:bingo |
Hits:
Description: 这里有OQPSK的调制源程序代码，用matlab做的，很好，需要的可以在这里下载-There are OQPSK modulation source code, using matlab to do, and very good, needs can be downloaded here Platform: |
Size: 1024 |
Author:孙政委 |
Hits:
Description: BPSK在AWGN信道下的仿真程序，matlab代码，功能齐全，是一个很好的平台-BPSK in AWGN channel under the simulation program, matlab code, full-featured, is a good platform Platform: |
Size: 1024 |
Author:张明 |
Hits:
Description: 无线通信系统中的常用仿真代码QPSK调制的MATLAB代码-Wireless communication systems commonly used in the simulation of MATLAB code QPSK modulation code Platform: |
Size: 15360 |
Author:毛山明 |
Hits:
Description: 源码中包括了QPSK的调制与解调，以及QPSK信号比特误码率的计算-Source code included in the QPSK modulation and demodulation, as well as the QPSK signal bit error rate calculation Platform: |
Size: 2048 |
Author:丘实 |
Hits:
Description: 使用matlab程序实现了由随机序列到码元电平、m序列直接扩频解扩、qpsk调制解调，射频调制解调一个完整的qpsk系统过程-Matlab program to use by the random sequence to the symbol level, m direct sequence spread spectrum despreading, qpsk modulation and demodulation, RF modulation and demodulation of the QPSK system, a complete process Platform: |
Size: 8192 |
Author:朱丽平 |
Hits:
Description: mpsk生成代码,各种方式生成的代码 ，包括2psk,qpsk,8psk,16psk等-MPSK generate code, generate code in various ways, including 2psk, qpsk, 8psk, 16psk such as Platform: |
Size: 1024 |
Author:张超凡 |
Hits:
Description: 提出了一个采用(2,1,7)卷积码+QPSK的中频调制解调方案,并在Xilinx公司的100万
门FPGA芯片上实现了该系统。该系统在信噪比SNR为6dB左右时可实现速率超过1Mbit/s、误码率
小于10-5的数据传输。
-Proposed a use of (2,1,7) convolutional code+ QPSK modulation and demodulation of the IF program, and in Xilinx' s FPGA chip one million on implementation of the system. The system SNR to 6dB signal to noise ratio at about the rate may achieve more than 1Mbit/s, less than 10-5 bit error rate of data transmission. Platform: |
Size: 62464 |
Author:张同星 |
Hits:
Description: Matlab代码实现了一个调制的GUI界面，同时实现了ASK, OOK, BPSK, QPSK, 8PSK调制算法的源代码。以图像形式展示了各种调制算法的实际运行结果。
-Matlab code implementation of a modulation GUI interface, at the same time achieve the ASK, OOK, BPSK, QPSK, 8PSK modulation algorithm source code. Image form a variety of modulation algorithm to display the actual results. Platform: |
Size: 4096 |
Author:林文媛 |
Hits:
Description: This file is the matlab source code for offset QPSK (OQPSK) modulation and demodulation in wireless and mobile communications Platform: |
Size: 1024 |
Author:Abbas |
Hits:
Description: QPSK信号在MATLAB上的仿真代码，载波频率为10HZ，信息速率为1Baud，信号经过带宽为2HZ的系统。-QPSK signal in the simulation of MATLAB code, the carrier frequency to 10HZ, the information rate of 1Baud, signal bandwidth of the system 2HZ. Platform: |
Size: 706560 |
Author:小武 |
Hits:
Search - matlab code QPSK