Location:
Search - Proteus V7
Search list
Description: MPLAB V7.11 HI-TECH V8.05 Proteus V7.1
现在这只是一个简单的加法计算器,当前使用方法：
1) 输入第一个数(<4位)；边输入边显示
2) 按＋号；清空数码管；
3) 输第二个数(<4位) ； 边输入边显示
4) 按＝号出结果；显示在数码管上
5) 按C号，返回1) 继续等待输入
Platform: |
Size: 81190 |
Author: backup |
Hits:
Description: 《单片机原理实用教程——基于Proteus虚拟仿真》一书的配套光盘，光盘内容为书中各章例题的Proteus设计范例以及汇编语言源程序。
所有范例均在Proteus V7.2之下调试通过。范例必须在安装Proteus软件之后才能运行。- All examples are under the debugger through the Proteus V7.2. Example Proteus software must be installed to run after.
Platform: |
Size: 1884160 |
Author: 王祖龙 |
Hits:
Description: 采用模块化格式编写的基于PIC单片机的简单计算器，采用4*4键盘输入，4位数码管输出,电路图为kb16seg74ok.DSN。 MPLAB V7.1+HI-TECH V8.05+Proteus V7.1-Modular format PIC MCU-based simple calculator, the use of 4* 4 keyboard input, 4 digital tube output circuit for kb16seg74ok.DSN. MPLAB V7.1+ HI-TECH V8.05+ Proteus V7.1
Platform: |
Size: 80896 |
Author: 王萧风 |
Hits:
Description: 郭天祥 TX-1C PIC单片机实验板proteus V7.0版本。 使用7.0以上的Proteus均可打开使用。-Guo Tianxiang TX-1C PIC Microcontroller Experiment board proteus V7.0 version of the. Of more than 7.0 can be used to open the use of Proteus.
Platform: |
Size: 37888 |
Author: 王萧风 |
Hits:
Description: Operating System threaded apartment done in the PIC16F877A and communication to the PC through RS232 protocol which is displayed in an interface made in Visual C #.
The simulation was conducted in the PROTEUS software v-Operating System threaded apartment done in the PIC16F877A and communication to the PC through RS232 protocol which is displayed in an interface made in Visual C #.
The simulation was conducted in the PROTEUS software v7.7.
Platform: |
Size: 4424704 |
Author: RollyMark |
Hits:
Description: PIC单片机SPWM例子，采用硬件PWM实现。外部电路非常简单，在RC1上接一个电容即可。
开发环境：MPLAB IDE V8.60+HT-PICC16 V9.80 pro PJ版+Proteus V7.1PJ版。 -PIC microcontroller SPWM example, using the hardware PWM to achieve.
Development Environment: MPLAB IDE V8.60 HT-PICC16 V9.80 pro PJ version of Proteus V7.1PJ version.
Platform: |
Size: 94208 |
Author: 王萧风 |
Hits:
Description: 周立功arm7单片机 pl2124在proteus上的仿真，包括原理图与仿真代码，开发环境为proteus 喝keil4-the simulation project of arm pl2124 on proteus,includes schematic and source code ,developed with proteus v7 and keil v4
Platform: |
Size: 1551360 |
Author: 杨风 |
Hits:
Description: If you are afraid of soldering Nokia LCD with your hands and still want to check your code..
here is a solution for you..
One of our Russian friend has made this sweet Nokia 3310 LCD model which simulate the original Nokia LCD.
This Proteus model has been tested with the following versions of Proteus VSM Co-simulator
Proteus v6.9 SP5
Proteus v7.2 SP2
Proteus v7.4 SP3
Proteus v7.5 SP3
Proteus V7.6 (service pack unknown) - will update soon
Platform: |
Size: 407552 |
Author: rajesh vana |
Hits:
Description: 自制的ATMEGA16的PROTEUS开发板，包含如下组件：8个发光二极管、液晶显示器1602、矩阵键盘、IO独立键盘、串口调试器、8位8段数码管、SPI接口调试器、时钟、存储器24c02等。-An ATMEGA16 develop board circuit drawed in ISIS Proteus v7.7.The components it contains are as follows:eight LEDs linked to P1,dot array LCD 1602,four lines multiply four columns matrix keypad,eight buttons link directly to P3,SPI and IIC debuger,eight bits segments,DS1302 RTC with IIC interface, EEPROM memory IC 24c02.
Platform: |
Size: 50176 |
Author: E.P.Wolf |
Hits:
Description: 采用PIC16F877A单片机实现多片DS182B在单线总线下的多点温度测量
开发环境：微芯MPLAB+PICC编译器
仿真环境：Proteus v7.5-Using PIC16F877A MCU multi-chip single-wire bus DS182B in multi-point temperature measurement.
Development environment: Microchip MPLAB+PICC compiler.
Simulation environment: Proteus v7.5
Platform: |
Size: 169984 |
Author: WLiang |
Hits:
Description: 利用PIC16F877单片机实现简单的DDS信号发生器
开发环境：微芯MPLAB IDE+PICC编译器
仿真环境：Proteus v7.5-Adopt PIC16F877 MCU to realize simple DDS signal generator.
Development environment: Microchip MPLAB IDE+PICC compiler.
Simulation environment: Proteus v7.5
Platform: |
Size: 155648 |
Author: WLiang |
Hits:
Description: 利用PIC16F877单片机驱动64*128的液晶模块LCM12864.
开发环境：微芯 MPLAB+PICC编译器
仿真环境：Proteus v7.5-Use PIC16F877 MCU to drive 64*128 LCD module LCM12864.
Development environment: Microchip MPLAB+PICC compiler
Simulation environment: Proteus v7.5
Platform: |
Size: 885760 |
Author: WLiang |
Hits:
Description: PIC 16F628A based time relay project.
C and PICBasic codes included.
schematic and PCB included (Proteus V7).
Platform: |
Size: 157696 |
Author: orhan |
Hits:
Description: 本设计设计手机充电器系统，实现由交流220V电能到直流4.2V电能的转换，进而为手机等设备充电。在系统控制中采用了变压、整流、滤波、稳压、分压、电压检测等电路，并且具有一定的充电提示和充满电自动断电的功能。
本设计采用Proteus（V7.1）软件仿真进行演示。-Based on Proteus simulation design phone charger system, implemented by 220V AC power to DC 4.2V power conversion. In control system uses a transformer, rectifier, filter, regulator, voltage divider, the voltage detection circuit, and has some tips and full power charging automatic power-off function.
Platform: |
Size: 573440 |
Author: LCH |
Hits: