Location:
Search - JTAG
Search list
Description: 一个通用的JTAG烧写程序,本人对其进行了性能的扩充,使其可以支持更多的处理器类型,如S3C2410,AT9200等.使其更具通用性.-A general JTAG burning program, I extend its performance to support more CPU types, such as S3C2410, AT9200, etc. This enhances its generality.
Platform: |
Size: 323584 |
Author: 吴鹏 |
Hits:
Description: JTAG接口驱动程序,可以帮助初学程序下载的朋友。-JTAG interface drivers, can help beginners download friends.
Platform: |
Size: 51200 |
Author: bin |
Hits:
Description: verilog 实现的jtag ip模块
包括了测试程序-Verilog achieve the JTAG ip modules including test procedures
Platform: |
Size: 6144 |
Author: 陈俊 |
Hits:
Description: JTAG的驱动程序，一般都是用在相对应的嵌入式ARM处理器上，这个事实用在LPC2210上面。-JTAG drivers are generally used in relation to the embedded ARM processor, with the fact that the LPC2210 above.
Platform: |
Size: 24576 |
Author: 万文辉 |
Hits:
Description: 该文档介绍了使用JTAG口在ARM体系CPU芯片中如何进行调试。-The document describes the use of JTAG mouth in the ARM CPU chip debug how.
Platform: |
Size: 192512 |
Author: 马欣 |
Hits:
Description: 通过ARM JTAG的FLASH芯片烧写程序源代码，已经验证过可以正常运行。-through the ARM chip JTAG FLASH burning program's source code has proven it works.
Platform: |
Size: 671744 |
Author: 贺亚龙 |
Hits:
Description: Segger JTAG Debugger
Platform: |
Size: 1541120 |
Author: Sim |
Hits:
Description: 这是基于UP-ARM2410开发板的实验，这是第一次实验，目的是熟悉ADS调试工具以及JTAG工具-This is based on the UP-ARM2410 development board experiments, this is the first time experiments, ADS is familiar with the tools and JTAG debugging tools
Platform: |
Size: 834560 |
Author: 王海滨 |
Hits:
Description: 1）通过fs44b0xbios和网口，将upload里的boot.bin烧写到flash 0 地址
见“FS44B0Xbios使用指南”之5
2) 打开57600超级终端
3) 连上串口线和jtag调试头
4）打开FS44B0X开发板电源
5）运行jtag.exe,在SDT下调入 ucosii_demo.axf，运行
6) 在超级终端上有三个任务的运行与退出显示，板子上的三个发光二极管会来回闪烁。
-a) fs44b0xbios and LAN, li will upload the burning of flash boot.bin 0 addresses see "FS44B0Xbio s User's Guide "5 2) to open 57,600 Super Terminal 3) connected to serial lines and the first four JTAG Debugging) Open FS44B0X development board Power 5) Run jtag.exe, under the redeployment ucosii_demo.axf SDT, running 6) of the Super Terminal 3 on the mandate of the operation and withdraw from the show, on board the three light-emitting diodes will flicker back and forth.
Platform: |
Size: 215040 |
Author: 张淼林 |
Hits:
Description: DIY轻松制作MSP430 JTAG 完整压缩包。-DIY easily produced MSP430 JTAG integrity compressed.
Platform: |
Size: 4744192 |
Author: 王晗 |
Hits:
Description: AVR ISP/JTAG下载器全部资料,包括原理图/PCB/烧录的文件.支持AVR STDIO下载.-AVR ISP/JTAG download for all information, including schematics/PCB/copying documents. Support AVR STDIO download.
Platform: |
Size: 250880 |
Author: 小文子 |
Hits:
Description: MSP430单片机JTAG，PROTEL原理图及PCB板图-MSP430 JTAG, PROTEL schematics and PCB plans
Platform: |
Size: 72704 |
Author: john |
Hits:
Description: Open Jtag小组的产品。有了它，您将可以用简易并口JTAG小板在ADS中进行调试！感谢twentyone的杰出工作！-Open Jtag Group products. With it, you can use simple parallel port JTAG small plate in the ADS for debugging! Twentyone grateful for the excellent work!
Platform: |
Size: 439296 |
Author: 李伟 |
Hits:
Description: JTAG CPLD实现源代码，比用简单并口调试器快5倍以上。
以前总觉得简单的并口jtag板速度太慢，特别是调试bootloader的时候，简直难以忍受。最近没什么事情，于是补习了几天vhdl，用cpld实现了一个快速的jtag转换板。cpld用epm7128stc100-15，晶振20兆，tck频率5兆。用sjf2410作测试，以前写50k的文件用时5分钟，现在则是50秒左右。tck的频率还可以加倍，但是不太稳定，而且速度的瓶颈已经不在tck这里，而在通讯上面了。
-JTAG CPLD source code than the simple parallel debugger five times faster. Before feel simple parallel port JTAG board is too slow, especially when debugging Bootloader, simply intolerable. No matter recently, so VHDL tutorial for a few days, with cpld to achieve a rapid conversion of JTAG board. Cpld with epm7128stc100-15, 20 Katherine crystal, the frequency tck 5 trillion. Sjf2410 used for testing, before the document was made with 50k at 5 minutes, now it is about 50 seconds. Tck frequencies can also doubled, but not too stable, but the rate has not tck bottleneck here, and in the above communications.
Platform: |
Size: 2048 |
Author: 李伟 |
Hits:
Description: XilinxJTAG.rar
xilinx CPLD,FPGA的JTAG口使用说明.-XilinxJTAG.rar Xilinx CPLD, FPGA JTAG I use.
Platform: |
Size: 431104 |
Author: |
Hits:
Description: 这篇文章主要介绍ARM JTAG调试的基本原理。基本的内容包括了TAP (TEST ACCESS PORT) 和BOUNDARY-SCAN ARCHITECTURE的介绍，在此基础上，结合ARM7TDMI详细介绍了的JTAG调试原理。-This article introduces the ARM JTAG debugging basic tenets. The basic elements include the TAP (TEST PORT ACCESS) and BOUNDARY- SCAN ARCHITECTURE presentation on this basis, the combined ARM7TDMI details of the principles of JTAG debugging.
Platform: |
Size: 453632 |
Author: 宋磊 |
Hits:
Description: 这个程序是我自己写的，主要用于PXA255的烧写，经过我修改后，特别方便JTAG下，CPU的调试，可以测试CPU的各个IO脚，无需跑操作系统，即可简单查看外设是否正常。参照APP子目录下的使用方法即可。在微软的JflashMM上做了修改。-I wrote it myself, mainly for the PXA255 burning, I have revised, especially convenient JTAG, the CPU test, the CPU can test various IO feet without running the operating system, simple View peripherals can be normal. APP subdirectory under the light of the method can be used. Microsoft has done a JflashMM changes.
Platform: |
Size: 112640 |
Author: 王成云 |
Hits:
Description: xilinx FPGA上使用jtag接口作为用户IO的源码。支持任意位宽度。-Xilinx FPGAs use JTAG interface as user IO source. Support for arbitrary bit width.
Platform: |
Size: 1024 |
Author: 尹成科 |
Hits:
Description: eeprom和flash是自制JTAG的源程序，熔丝配置位图为写MG16时的熔丝配置情况。
-EEPROM and flash is a self-made JTAG source, Fuse-allocation map was made MG16 the Fuse configurations.
Platform: |
Size: 652288 |
Author: 王宇 |
Hits:
Description: 把uCOS移植到三星的44B0的CPU上面，不过是在IAR环境下的，代码是2.80的，还带uCGUI哦，用IAR for ARM 4.31和H-JTAG验证通过。个人认为可以媲美官方版本的移植。-put uCOS transplanted to the 44B0 Samsung CPU above, but in the IAR environment, the code is 2.80, also brings uCGUI Oh, IAR used for the ARM 4.31 and H- JTAG test passed. Individuals that can be comparable to the official version of the transplant.
Platform: |
Size: 764928 |
Author: 张凡 |
Hits:
«
1
2
...
7
8
9
10
11
1213
14
15
16
17
...
50
»