Location:
Search - C-Minus
Search list
Description: 除法器的设计本文所采用的除法原理是：对于八位无符号被除数A，先对A转换成高八位是0低八位是A的数C，在时钟脉冲的每个上升沿C 向左移动一位，最后一位补零，同时判断C的高八位是否大于除数B，如是则C的高八位减去B，同时进行移位操作，将C的第二位置1。否则，继续移位操作。经过八个周期后，所得到的C的高八位为余数，第八位为商。从图(1)可清楚地看出此除法器的工作原理。此除法器主要包括比较器、减法器、移位器、控制器等模块。-Divider design used in this paper, the principle of division is: For the eight unsigned dividend A, the first of A into the high-low 8 0 8 is the A number of C, in each clock rising edge to the left C Mobile One, and finally a zero, at the same time to determine whether C is greater than the high-8 divisor B, so is the high C 8 minus B, at the same time shift operation, the location will be C s second one. Otherwise, continue to shift operation. After eight cycles, received a high C for more than eight the number of eighth place for the business. From Figure (1) can clearly see that the divider works. This mainly includes divider comparators, subtraction, and shifter, controller modules.
Platform: |
Size: 4096 |
Author: 老毕 |
Hits:
Description: 最新仙镜传说服务器C语言源码
Retouch about problem of increase in quantity at the CART,-最新仙镜传说服务器C语言源码
Retouch about problem of increase in quantity at the CART,
when enter the an minus quantity in the CLIENT.
Retouch about problem of not recovery,use POTIONPITCHER skill.
(map/)
battle.c
battle_heal()
vending.c
vending_purchasereq()
Platform: |
Size: 1234944 |
Author: 王小雨 |
Hits:
Description: 他是C语言写的程序集包含了属性约减、属性值约减等诸多算法-He is a program written in C language contains the attribute reduction, attribute values such as about minus algorithm
Platform: |
Size: 181248 |
Author: baoyujun |
Hits:
Description: 利用C语言实现键盘控制数码管显示值加1或减1-The use of C language realization of the keyboard to control the digital display the value of plus 1 or minus 1
Platform: |
Size: 4096 |
Author: marry |
Hits:
Description: 本设计的主要内容是用单片机系统进行温度实时采集与控制。温度信号由AD590K和温度／电压转换电路提供，对AD590K进行了精度优于正负0.1°C的非线性补偿，温度实时控制采用分段非线性和积分分离PI算法，其分段点是设定温度的函数。控制输出来用脉冲移相触发可控硅来调节加热丝有效功率。系统具备较高的测量精度和控制精度-The main content of this design is to use real-time microcontroller system acquisition and control the temperature. Temperature signal from the AD590K and temperature/voltage conversion circuit provided on the AD590K was plus or minus 0.1 ° C accuracy of better than non-linear compensation, the temperature real-time control and integration with sub-linear algorithm for separation of PI and its sub-point is Set a function of temperature. Control output to trigger a pulse thyristor phase-shift effective power to regulate the heating wire. The system has a higher measurement precision and control accuracy
Platform: |
Size: 355328 |
Author: wang |
Hits:
Description: 大数四则运算,实现加减乘除以及模运算,c++语言实验，比较实用-big number algorithm，add,minus,multiple and mod
Platform: |
Size: 273408 |
Author: 李好 |
Hits:
Description: 本设计以STC89C516RD+单片机为控制运算器，以8*6矩阵键盘控制，以12864ZB液晶显示，以9V电池供电。
对于此计算器我用了38个键的矩阵键盘，10个数字键，1个小数点键，1个正负键，4个常用运算键，1个等号键，1个清零键，1个第二功能键，4个三角函数运算键，4个常用公式键，还有8个其它功能键。此计算器与常用计算器无很大差别，其中四则运算、阶乘、百分比、平方、立方、组合、乘方、倒数都可以精确到十位 ，其它运算因为调用到C语言函数库，为浮点型，有效位只有7位。
-The design use STC89C516RD+ MCU to control the computing device, On 8*6 keyboard control, with 12864ZB matrix liquid crystal display (LCD),9v battery power.
For this calculator I used a matrix of 38 keys keyboard, 10 numeric keys, a decimal point key, a plus or minus keys, four common operation keys, an equal sign key, a Clear key, a The second function keys, four trigonometric functions keys, four commonly used formula keys, there are eight other function keys. This calculator and the calculator was no significant difference in common, including arithmetic, factorials, percentages, squares, cubes, mix, involution, the countdown can be accurate to 10, other operations because the call to C language function library for floating-point type, the effective bit only seven.
Keywords: Single-chip dot-matrix graphic LCD matrix keyboard C language library function.
Platform: |
Size: 77824 |
Author: huangyanfeng |
Hits:
Description: You can calculate some arithmetic operation using Visual C++ tool. (plus, minus, division, multiplication)
Platform: |
Size: 1024 |
Author: chulhyun |
Hits:
Description: 常用的基本功能实现程序都有,比如说加，减等等基本功能运算。-source code of c language ,you can find many basic codes.for example,plus ,minus,mutiply,divide, and so on.
Platform: |
Size: 1816576 |
Author: ly |
Hits:
Description: 单片机电子钟，用C语言开发。
设计制作一个电子钟并且能够显示日历，用LED数码管直接显示，能够通过按键调整时间、年月日，功能为按第一个键为Mode（模式）键，被调整的相应调整区域开始闪烁，第二个键（Add键）加一，第三个（Sub键）减一，中间的键（Add键）可以使时分秒和年月日相互切换。-MCU clock, using C language development. Designed an electronic clock and can display a calendar, with LED digital display directly, through buttons adjust the time, years on, press the function key for the first Mode (mode) key areas to be adjusted to adjust the flashes, the first Two button (Add button) plus a third (Sub key) minus one, the middle button (Add button) can make each day, hour, and the years to switch.
Platform: |
Size: 300032 |
Author: sunrise_kailun |
Hits:
Description: 硫酸铜建浴设备控制系统
具体控制要求: 1.按下 P3.4和P3.5不放 按下 P3.7 即可进入设置模式，再次按下退出设置模式
左边四位数码管最左边的开始闪烁，后面的四位数码管不属于此控制系统 *
按下加或减 有 A b C 三档 分别代表三个参数。 *
第一个参数(A)：搅拌机运行时间 *
第二个参数(b)：液位信号保持时间 *
第三个参数(C): 为定义 *
-Copper sulfate bath equipment control system built specifically control requirements: 1. Press and hold press P3.7 P3.4 and P3.5 to enter the setting mode, press again to exit the setup mode on the left of the left-most four digital start flash, followed by four digital control system* does not belong to this press plus or minus a A b C represent the three parameters third gear.* The first parameter (A): mixer running time* The second parameter (b): liquid level signal hold time* the third parameter (C): the definition of*
Platform: |
Size: 164864 |
Author: 张成 |
Hits:
Description: 两相5、6线步进电机，分为四拍和八拍，这里介绍输出八拍方式：A-AC-C-CB-B-BD-D-DA
//四拍：A-C-B-D，因此在八拍的基础上减去中间的就可以了，不过步距角要大一倍-Two-phase stepper motor 5,6 lines, divided into four beats and eight shot, and here eight shot output mode: A-AC-C-CB-B-BD-D-DA// four beats: ACBD, so eight based on the film minus the middle of the can, but want to double the step angle
Platform: |
Size: 1024 |
Author: leso |
Hits:
Description: 按下 P3.4和P3.5不放 按下 P3.7 即可进入设置模式，再次按下退出设置模式， 左边四位数码管最左边的开始闪烁，后面的四位数码管不属于此控制系统， 按下加或减 有 A b C 三档 分别代表三个参数。第一个参数(A)：搅拌机运行时间，第二个参数(b)：液位信号保持时间-Press P3.4 and P3.5 doesn t put press P3.7 can enter setup mode, again press exit setting mode, the left four digital tube the left-most flickered on, behind of four digital tube does not belong to this control system, press the plus or minus have A b C three gears respectively represent three parameters the first parameter (A) : mixer running time, the second parameter (b) : level signal
Platform: |
Size: 52224 |
Author: zhouhao |
Hits:
Description: 这是基于单片机的使用C语言的设计。可以自动显示时分秒。使用按键可以实现时加1和时减1-This is the use of C language based on single chip design. Can automatically display minutes and seconds. Can be achieved when using the keys plus 1 and minus 1 when
Platform: |
Size: 11264 |
Author: 李佳 |
Hits:
Description: 刚学到printf函数和scan函数，很是一个不清楚，求几段经典范例代码，初学者入门用的。
另外有几道题求解，万分感谢！！
1.试尽量用多种不同的C代码，描述把整型变量i的值增加1的运算
2.试分别用最紧凑的一条C代码描述完成下列计算
1）把整型变量i和j的和赋给整型变量k，并同时让i的值增加1.
2）把整型变量X值扩大一倍
3）在变量i减去1后，将变量j减去变量i
4）计算变量i除变量j的余数r-Printf function and scan just learned function, it is a clear, find the classic example of code paragraphs, beginner use. Another problem solved Jidao extremely grateful! ! 1. Try as much as possible with a variety of C code, describes the value of the integer variable i by 1 computation 2. Subjects were the most compact description of a C code to complete the following calculation 1), the integer variable i and j, and assigned to the integer variable k, and also to increase the value of i 1.2) to double the size of an integer value of the variable X 3) minus 1 in the variable i, after subtracting the variable j variable i 4) In addition to calculating the variable i the remainder of the variable r j
Platform: |
Size: 3072 |
Author: 朱军华 |
Hits:
Description: 一个C程序，其想要输出20个减号，不过，粗心的程序员把代码写错了，你需要把下面的代码修改正确，不过，你只能增加或是修改其中的一个字符，给出三种答案。-A C program, its desired output of 20 minus sign, but the careless programmer to code wrong, you need to modify the following code is correct, but you can only add or modify one of the characters, given three kinds of answers.
Platform: |
Size: 14336 |
Author: 翟健 |
Hits:
Description: 基于Visual C++的建议计算器，可实现多位浮点数的加减乘除-Calculator，can be used to calculate plus, minus, multiply and except.
Platform: |
Size: 3270656 |
Author: nzncy |
Hits:
Description: 在C++中实现两个数的加，减，乘，除及比大小-Two numbers in C++, plus, minus, multiply, with the exception than the size of
Platform: |
Size: 1098752 |
Author: 李晨 |
Hits:
Description: The img2tif program converts an Imagine .img file into one or more GeoTIFF files.
Usage: img2tif [-i img_filename] [-o tif_basename] [-c] [-v n...]
[-rgb [red_band green_band blue_band]] [-?] [-quiet]
Arguments:
-i input .img file
-o output base file name
Output files will be named base_name1.tif ... base_nameN.tif,
where N = no. of bands.
-rgb produce an RGB image file from the indicated band numbers
within an existing imagine file.
-s output file is in strips (tiles is default)
-c packbits compress flag (def=uncompressed)
-v overview sampling increment(s) (0=single, 98=full set minus 2x,
99=full set) Examples: -v 2 4 8 -v 0 -v 99
-quiet Don t produce a translation report.
-? Print this explanation of command line arguments-The img2tif program converts an Imagine .img file into one or more GeoTIFF files.
Usage: img2tif [-i img_filename] [-o tif_basename] [-c] [-v n...]
[-rgb [red_band green_band blue_band]] [-?] [-quiet]
Arguments:
-i input .img file
-o output base file name
Output files will be named base_name1.tif ... base_nameN.tif,
where N = no. of bands.
-rgb produce an RGB image file from the indicated band numbers
within an existing imagine file.
-s output file is in strips (tiles is default)
-c packbits compress flag (def=uncompressed)
-v overview sampling increment(s) (0=single, 98=full set minus 2x,
99=full set) Examples: -v 2 4 8 -v 0 -v 99
-quiet Don t produce a translation report.
-? Print this explanation of command line arguments
Platform: |
Size: 1370112 |
Author: Alex |
Hits:
Description: 16字 LED点阵屏+DS1302电子钟 C 程序1 脚接+5V 2，3脚32768HZ晶振 4脚接地 5脚接S51的P02 6脚接S51的P01 7接S51的P008脚接后备电源，可以接老计算机主板板上的3.6V电池，也可以通过二级管隔离接一个大容量电解电容电压在2.5V以上即可维持595连级输出数据，138行驱动 P1_0为时钟模式转换键、P2_1为时钟加键、P1_2为时钟减键、P2_3为时钟复
-C program of the 16-character LED dot matrix display+DS1302 electronic clock pin+5V 2,3 feet 32768HZ crystal 4 foot ground five feet of the P01 to P02 6 pin access S51' s S51 then S51 P008 pin back-up power, you can access the old computer motherboard board 3.6V battery can also be connected through two tubes isolation can maintain a large-capacity electrolytic capacitor voltage of 2.5V above output data of the 595 company-sized, 138-line-driven P1_0 clock mode conversion key, P2_1 clock plus key , P1_2 clock minus key P2_3 complex as the clock
Platform: |
Size: 4096 |
Author: 尴尬 |
Hits: