Search - Gravity

Search - Gravity - List

[Other Embeded program] SRB DL : 0: ZIGBEE WSN 无线三轴重力加速度传感器网络节点程序-ZIGBEE WSN wireless three-axis gravity sensor network node procedure
Date : 2026-01-09 Size : 293kb User : dfdf
[Other Embeded program] NCB DL : 0: zigbee无线三轴重力加速度NCB程序，与SRB相对应。-zigbee wireless three-axis acceleration of gravity NCB procedures, and the corresponding SRB.
Date : 2026-01-09 Size : 313kb User : dfdf
[Other Embeded program] RealFinal DL : 0: 智能测距，提示报警，温度测量，语音报警，具体芯片51，重力感应，倾角测量-Smart ranging, prompted alarm, temperature measurement, voice alarm, the specific chip 51, gravity sensor, inclination measurements
Date : 2026-01-09 Size : 5kb User : guy
[Other Embeded program] pidaicheng DL : 0: 设计单片机系统拟实现电子调速皮带秤。本系统利用称重传感器测量输送带有效称量段上物料的重量，并将被测重力转换成相应的模拟电压信号，经放大器放大后，由A/D转换成数字量。与此同时，速度传感器将皮带速度转换为计数脉冲后进行整形。2路信号都送到C8051F410中进行计算、处理，得到当前皮带秤的瞬时流量值，对瞬时流量进行积分得到一段时间内的累积重量。瞬时流量与给定流量进行计较，运用PID算法，输出控制信号控制变频器来改变电机转速，从而可以实现流量的闭环控制。此部分需要设计2路信号输入通道，分别为称重传感器的模拟信号输入通道以及测速传感器的频率信号输入通道，同时还有一路模拟输出信号通道，输出1-5V电压信号来驱动变频器工作。另外还需要键盘显示模块以及通信模块，此部分需要完成参数设定、数字显示以及数据上传等功能。-Design SCM system intends to realize electronic speed belt scale this system use weighing sensor measurement conveyor belt effective weighing section on the weight of the materials, and the measured gravity converted into corresponding analog voltage signal, the amplifier amplification, the A/D convert digital quantity and the same time, speed sensor will belt speed conversion for counting pulse shaping after 2 road signals are sent to the C8051F410 calculation processing, get the current belt scale of instantaneous flow rate value, the instantaneous flow integral for A period of time inside of cumulative weight instantaneous flow and A given flow object, using PID algorithm, output control signal control frequency converter to change motor speed, which can realize the flow of closed loop control this part need to design 2 road signal input channel, respectively weighing sensor analog signal
Date : 2026-01-09 Size : 7kb User : 王聪
[Other Embeded program] Acceleration-sensor DL : 0: 基于msp430平台重力加速度传感器程序设计-Design-based the MSP430 platform for the acceleration due to gravity sensor program
Date : 2026-01-09 Size : 126kb User : jinshan
[Other Embeded program] ADXL345 DL : 1: 在stm32迷你板上实现ADXL345传感器的三轴重力加速度检测-Mini stm32 board to achieve the ADXL345 three-axis gravity sensor detection
Date : 2026-01-09 Size : 1.37mb User : 陈国东
[Other Embeded program] angle-sensor DL : 0: 这是一个倾角测量与显示的程序，它能测出任何物体的倾角,即与重力方向的夹角，然后可以帮助该物体做出调整,液晶显示为了调程序方便而用的.-This is an angle measurement and display program, it can measure the angle of any object, i.e. the angle between the direction of gravity, and can help to adjust the object, a liquid crystal display to adjust the program used for convenience.
Date : 2026-01-09 Size : 45kb User : liuxiaoxu
[Other Embeded program] mma8451 DL : 0: mma8451角度传感器程序。能精确测出物体倾斜角度以及三个方向的重力加速度。-mma8451 angle sensor program. To accurately measure the tilt angle of the object and the acceleration of gravity in three directions.
Date : 2026-01-09 Size : 60kb User : 桐
[Other Embeded program] Acceleration(MMA7455L) DL : 0: 基于STM32模拟MMA7455L芯片的重力加速度-MMA7455L based STM32 chip simulation acceleration of gravity
Date : 2026-01-09 Size : 4.43mb User : future
[Other Embeded program] G DL : 0: 重力加速度计ADXL313倾角测量程序，C8051F041通过I2C进行读写控制，实测有效，倾角分辨率小于1度。-Gravity accelerometer ADXL313 angle measurement procedure, C8051F041 controlled via I2C read and write, found effective resolution of less than 1 degree inclination.
Date : 2026-01-09 Size : 2kb User : samson
[Other Embeded program] motion_driver_6.12 DL : 0: 最新的MPU9250,MPU9150,MPU6050,MPU6500官方资料-Changes Notes- MD6.1 to 6.12 - Fixed Hardware Calibration Offset register accel format Previous implementation was saving the offsets in the accel offset registers in a scalre range of+-8G. After clarification the format should be saved in scale range of+-16G - Fixed sometimes for 9-axis sensor fusion new data flag is not updated In hal_outputs.c, there is a flag which indicates when there is new 9-axis data to be pushed into the MPL library to be built. Flag was looking into the wrong settings to be set. - added gravity vector data output Gravity vector will give on which axis the gravity is effecting on the accel. This way you can always see where the gravity is on the device - Added ARM precompiled MPL libaries for IAR, Keil, and GCC 4.9.3 Precompiled MPL libraries using IAR and Keil compiler for M0, M0+,M3, M4, M4F. GCC libraries updated to GCC 4.9.3 and there are M0, M3, and M4 with no FP, softFP, and hardFP. GCC compiler settings are based on
Date : 2026-01-09 Size : 23.08mb User : mupro
[Other Embeded program] MMA7455L DL : 0: 实现重力加速度模块的测量重力，用于STM32单片机-Realize the gravity gravity measurement module for STM32 Microcontroller
Date : 2026-01-09 Size : 4.62mb User : 王炀