Search - light off

Search - light off - List

[VHDL-FPGA-Verilog] jtd DL : 0: 这个是用verilog语言编写的基于FPGA的交通灯控制器，分别控制四个方向上的交通灯的通断-The verilog language is FPGA-based traffic light controller, respectively, the four direction control of traffic lights-off
Date : 2025-12-29 Size : 47kb User : jyb
[VHDL-FPGA-Verilog] PWM_LED DL : 0: 利用PWM控制LED亮灭的verilog程序，开发环境quartusII7.0-Using PWM control of LED light off a verilog program development environment quartusII7.0
Date : 2025-12-29 Size : 10mb User : 杜征宇
[VHDL-FPGA-Verilog] key_led_v DL : 0: 在quartus 2 环境下，基于verilog 语言实现按键_LED亮灭功能，并且编译通过，适合初学者。-In quartus 2 environment, based on verilog language button _LED light off function, and compile, for beginners.
Date : 2025-12-29 Size : 238kb User : 天良
[VHDL-FPGA-Verilog] SwitchLed DL : 0: FPGA入门程序。适合编程初学者的学习。由开关控制LED灯的亮灭。ISE集成开发环境。Verilog HDL语言编写-FPGA entry procedures. Programming for beginners to learn. LED lights from the light switch control off. ISE Integrated Development Environment. Language Verilog HDL
Date : 2025-12-29 Size : 239kb User : 李海波
[VHDL-FPGA-Verilog] FPGAshiyan(7) DL : 0: FPGA入门系列实验教程——实验七按键控制LED亮灭-Getting Started with FPGA tutorial series of experiments- experiments seven keys to control LED light off
Date : 2025-12-29 Size : 409kb User : lutangshi
[VHDL-FPGA-Verilog] keyboard DL : 0: 使用FPGA verilog语言编写的键盘按键消抖程序，三个按键，控制LED亮灭-Written using the FPGA verilog keyboard debounce procedure, three buttons, the control LED light off
Date : 2025-12-29 Size : 23kb User : 徐俊
[VHDL-FPGA-Verilog] digit-traffic-light DL : 0: 某交通管理部门要求，交通灯要求主干道绿灯至少保持2分钟（其中不包括绿灯闪烁时间），在此前提下，当支路检测到有车或人时，主干道绿灯闪烁3秒，然后黄灯持续亮3秒，红灯再亮，同时支路绿灯亮，红灯灭。当支路连续5秒检测不到车和人时，支路绿灯闪烁3秒，然后黄灯持续亮3秒，红灯再亮，同时主干道绿灯亮，红灯灭，支路绿灯最长持续20秒（不包括绿灯闪烁时间）。若从绿灯闪烁开始禁止支路上行人和车辆通行，则可保证主干道禁止通行的最长时间为26秒。支路可通过仪器来检测有无车辆和行人，对于行人，由于其不定性，需要设置一些仪器，如果有行人想通过，需站在其中一个检测仪下，当任一仪器检测到有车辆和行人要横穿主干道时，发出信号。由于主干道禁止通行的时间至多为26秒，因此，无需检测有无车辆和行人。- Requirements of a traffic management department, asked the main road traffic lights green for at least 2 minutes (not including the green light flashes the time), in this context, when the slip road vehicle or person is detected, the main road the green light flashes for 3 seconds, then yellow lamp is lit for 3 seconds, then red light, green light at the same time slip, red light off. When the slip is not detected continuously for 5 seconds when the cars and people, slip the green light flashes for 3 seconds, and then the yellow light is lit for 3 seconds, then red light, green light while the main road, the red light off, the longest continuous green slip 20 seconds (not including the green flashing light). If the green light flashes from a ban on pedestrian and vehicle traffic support on the road, you can ensure that the maximum time the main road closed to traffic for 26 seconds. Slip through the instrument to detect whether the vehicles and pedestrians, the pedestrians, because o
Date : 2025-12-29 Size : 203kb User : jamesheller
[VHDL-FPGA-Verilog] jtd DL : 0: 实现简单的交通灯功能25秒自动转换南北和东西方向红绿等亮灭-Simple 25 seconds of traffic lights function automatically converts red, green and other north-south and east-west light off
Date : 2025-12-29 Size : 137kb User : 竹鱼
[VHDL-FPGA-Verilog] turn_on_led DL : 0: _turn_on_led led亮灭实验-_turn_on_led led light off test
Date : 2025-12-29 Size : 1kb User : chen
[VHDL-FPGA-Verilog] key_led DL : 0: _key_led_without_debounce 轻触开关S1~S4 控制LED 亮灭，无按键去抖-_key_led_without_debounce touch switch S1 ~ S4 control the LED light off, no key debounce
Date : 2025-12-29 Size : 1kb User : chen
[VHDL-FPGA-Verilog] src DL : 0: _key_led_with_debounce 轻触开关S1~S4 控制LED 亮灭，有按键去抖-_key_led_with_debounce touch switch S1 ~ S4 control the LED light off, there are key debounce
Date : 2025-12-29 Size : 2kb User : chen
[VHDL-FPGA-Verilog] traffic DL : 0: CLK：为同步时钟； EN：使能信号，为1的话，则控制器开始工作； LAMPA：控制A方向四盏灯的亮灭；其中，LAMPA0~LAMPA3 ，分别控制A方向的-CLK: synchronized clock EN: Enable signal is 1, then the controller starts to work LAMPA: control the direction A four lamp light off which, LAMPA0, ~ LAMPA3, respectively, to control the direction of A
Date : 2025-12-29 Size : 314kb User : happy
[VHDL-FPGA-Verilog] qicheweideng DL : 0: 使用vhdl语言设计的汽车尾灯控制电路。用六个发光二极管模拟6个汽车尾灯（汽车尾部左,右各3个），用两个开关作为转弯控制信号（一个开关控制右转弯，另一个开关控制左转弯）。当汽车往前行驶时（此时两个开关的都未接通），6个灯全灭。当汽车转弯时，若右转弯（即右转开关接通），右边3个尾灯从左至右顺序亮灭，左边3个灯全灭；若左转弯（即左转开关接通），左边3个尾灯从右至左顺序亮灭，右边3个灯全灭。当左、右两个开关同时接通时，6个尾灯同时明、暗闪烁。 -The taillights control circuit using VHDL language design. Analog 6 automobile taillights (left of the rear of the car, the right of each 3) with six light emitting diodes, as a turn with the two switches the control signal (a switching control right turn, and another switch controls the left turn). When Previous traveling of the vehicle (when the two switches at this time none of ON), six light Quanmie. When the car turns, if the right turn (right turn switch is turned on), the right three taillights from left-to-right order of light off the left three light Quanmie left turn (ie turn left switch is turned on), the left The right-to-left order of a taillight light off, the right of three lights all off. When the left and right two switches simultaneously, 6 taillights and dark flashing.
Date : 2025-12-29 Size : 134kb User : 陈小龙
[VHDL-FPGA-Verilog] anjianxiaochudoudongkongzhiLED DL : 0: 实现按键控制LED 亮灭。通过这个实验，掌握采用Verilog HDL 语言编程实现按键控制LED 亮灭及按键消抖方法。-Buttons control the LED light off. Through this experiment, master Verilog HDL language programming buttons control the LED lights off and the key debounce.
Date : 2025-12-29 Size : 442kb User : 王恒
[VHDL-FPGA-Verilog] VHDL_qicheweideng DL : 0: VHDL语言，汽车尾灯的设计设计说明：共6个尾灯，汽车正常行驶时，6个灯全灭；左转时，左边3个灯从右到左依次亮灭；右转时，右边3个灯从左到右依次亮灭；刹车时，车灯全亮；故障时，全部闪烁。 -VHDL language, the design of the design of the taillights Description: six taillights, the normal running of the vehicle, six lights all off turn left, the three lights on the left from the right to the left turn light off turn right, the three lights on the right light off from left to right brakes, lights all bright fault, all flashing.
Date : 2025-12-29 Size : 50kb User : 李俊杰
[VHDL-FPGA-Verilog] exp2 DL : 0: 流水灯的实验，正转反转等功能，实现流水灯顺序亮灭。-Light water experiments, are forward reverse function, water lamp light off sequentially. .
Date : 2025-12-29 Size : 52kb User : zhaorongjian
[VHDL-FPGA-Verilog] LED_VHDL DL : 0: 用VHDL控制发光二极管,点亮发光二极管在熄灭发光二极管-VHDL control light off of the light-emitting diodes
Date : 2025-12-29 Size : 344kb User : lili
[VHDL-FPGA-Verilog] threelift DL : 0: （1）、每层电梯入口处设有上下请求开关，电梯内设有顾客到达层次的停站开关。（2）、设有电梯入口处位置指示装置及电梯运行模式(上升或下降)指示装置。（3）、电梯每秒升(降)一层楼。（4）、电梯到达有停站请求的楼层，经过 1 秒电梯门打开，开门指示灯亮，开门 4 秒后，电梯门关闭(开门指示灯灭)，电梯继续进行，直至执行完最后一个请求信号后停留在当前层。、能记忆电梯内外所有请求，并按照电梯运行规则按顺序响应，每个请求信号保留至执行后消除。、电梯运行规则当电梯处于上升模式时，只响应比电梯所在位置高的上楼请求信号，由下而上逐个执行，直到最后一个上楼请求执行完毕；如果高层有下楼请求，则直接升到由下楼请求的最高层，然后进入下降模式。当电梯处于下降模式时则与上升模式相反。、电梯初始状态为一层开门状态。-1), each request switch up and down the elevator entrance features, equipped with an elevator to reach the level of customer stop switch. (2) It has an elevator and the elevator entrance position indicating device operation mode (up or down) indicating device. (3), lift up (down) one floor per second. (4), there is an elevator to reach the requested floor stops, after one second elevator doors opened, the door lights, door four seconds later, the elevator doors closed (open light off), elevator continued until the end of the last execution request signal After staying at the current level. , Both inside and outside the elevator can remember all the requests and respond in accordance with the elevator in order to run the rule, each request to perform signal remains after the elimination. Elevator operating rules when the elevator is rising mode, where the only response is higher than the elevator upstairs request signal to perform bottom-up one by one until the last request is fini
Date : 2025-12-29 Size : 2.14mb User : 范志浩
[VHDL-FPGA-Verilog] 2112312 DL : 0: 模拟交通灯实验，实验报告用 8255 做输出口，控制十二个发光管（4 组红绿黄灯）的亮灭，模拟十字路口交通灯管理。-Simulated traffic light experiments report To do with the 8255 output, control twelve light tube (4 groups of red, green yellow) light off, analog crossroads traffic lights Management.
Date : 2025-12-29 Size : 89kb User : wwrkrwp
[VHDL-FPGA-Verilog] exp18 DL : 0: 这是一个vhdl的交通灯程序，可以实现两个方向间红、黄、绿灯之间的亮灭转换，同时还有秒表的计数、显示功能，为学习vhdl的人提供一定的技术参考。-This is a vhdl traffic lights procedures can be achieved between the two directions of red, yellow, green light off between the conversion, as well as the stopwatch count, display, provide a technical reference for learning vhdl person.
Date : 2025-12-29 Size : 1kb User : 殷超

« 12 3 »