Search - scale - CodeBus

[matlab] Scale-freeInternetsimulation

Description: 利用matlab软件编写的一类典型的复杂网络-无尺度网络的生成程序-Matlab software written using a class of typical complex networks- the generation of scale-free network program
Platform: | Size: 151552 | Author: 胡成 | Hits:

[Special Effects] 10.1.1.10.6587

Description: 利用MATLAB 实现RETINEX算法的实现步骤，涉及单尺度、多尺度等多种算法，适合初学者学习使用。-RETINEX algorithm using MATLAB implementation steps to achieve, involving a single-scale, multi-scale and other algorithms, suitable for beginners to use.
Platform: | Size: 951296 | Author: 王鹏 | Hits:

[SCM] weigh-scale

Description: Pic microcontroller for weight scaling
Platform: | Size: 1260544 | Author: nawaphun | Hits:

[Special Effects] SSR

Description: 实现单尺度retinex算法，用于图像的对比度增强，对低能见度图像处理效果较好。-Retinex single-scale algorithm for image contrast enhancement, image processing on low visibility is better.
Platform: | Size: 2048 | Author: 杨小黎 | Hits:

[matlab] scale_free

Description: 生成无标度序列，可以设定网络节点数及最小度数，画出了P（k）图，理解较容易。-Generate scale-free sequence, you can set the network nodes and the smallest degree, to draw the P (k) maps to understand more easily.
Platform: | Size: 2048 | Author: | Hits:

[Com Port] the-source-code-of-electronic-scale

Description: （1）初始化定时器与中断控制寄存器，初始化液晶显示器，设置串口通信波特率。（2）启动双积分AD转换过程，循环读取反向积分的计数值N，根据式3-7算出反向积分的计时值T2，换算出荷载重量值，送LCD显示。（3）每次换算出荷载重量值后，判断荷载是否超量程，如果超过系统量程2kg，则启动蜂鸣器报警。当荷载卸载至2kg以下后，解除报警。（4）如果有校准按键被按下，则响应外部中断0并查询按键编号，执行相应校准程序。（5）如果上位机软件STP_ISP发送了在线控制命令，则响应串口中断，接收并判断命令码，依据命令码执行校准程序并向上位机发送数据。 -(1) initial timer and interrupt control register, the initial LCD monitor, set the serial interface communication baud rate. (2) start double integral AD transform process, read backward integration project cycle numerical N, according to type 3-7 calculate backward integration project duration T2, conversion, send out load weight value LCD display. (3) every time a load weight after conversion value judgment, whether the measure range, load if more than 2 kg range, the system buzzer alarm. Start When load unloading to 2 kg, remove the alarm. (4) if there is calibration button is press, the response to external interruption and inquires the key Numbers, 0 executes calibration procedures. (5) if PC software STP_ISP send the online control command, the response, receiving and serial port interrupt judge ordered code, according to perform calibration procedures and command yards up a machine to send data.
Platform: | Size: 5120 | Author: ahuan | Hits:

[matlab] Solving-scale-free-networks

Description: 求解无标度网络,用于求解无标度网络模型的-Solving scale-free networks, for solving scale-free network model
Platform: | Size: 3072 | Author: wuhao | Hits:

[matlab] convolution

Description: This function is the function for the closed contour plot of the swing, then swing the plot padding made before the action, so the plot can take into account the entire swing closed contour, the program I used curvature scale space of his treatment another program curvature is used to calculate the location of high curvature points -This function is the function for the closed contour plot of the swing, then swing the plot padding made before the action, so the plot can take into account the entire swing closed contour, the program I used curvature scale space of his treatment another program curvature is used to calculate the location of high curvature points
Platform: | Size: 1024 | Author: upen | Hits:

[Special Effects] Image-gray-scale-transformation

Description: 详细说明：几个关于图像灰度变换的程序。包括图像反色，图像的对数灰度变换，指数灰度变换，线性灰度变换，灰度切割，图像平均降噪。-Several of the image gray-scale transformation process. Including anti-color image, the image of the number of gray level transformation, index gray-scale transformation, linear gray level transformation, gray cut, the average image noise.
Platform: | Size: 2048 | Author: lijie1 | Hits:

[Software Engineering] 1601.php

Description: am using 24 bit ADC(CS5460A) having a resolution of ~30 nv per bit and having a voltage range of -250mv to +250mv. Mine is jewellery weighing scale application and the voltage range is between +0.4mv to + 4.1mv. So the regsiter count should be between +13333 counts to +133000 approximately as mentioned by both of you. the readings i am getting are as follows. I have put the 24 bit data in Hex, Decimal and 2s complement notations in the below table. These values correspond to the 24 bit signed power register of the ADC. Power register is the product of current and voltage registers.-am using 24 bit ADC(CS5460A) having a resolution of ~30 nv per bit and having a voltage range of -250mv to +250mv. Mine is jewellery weighing scale application and the voltage range is between +0.4mv to + 4.1mv. So the regsiter count should be between +13333 counts to +133000 approximately as mentioned by both of you. the readings i am getting are as follows. I have put the 24 bit data in Hex, Decimal and 2s complement notations in the below table. These values correspond to the 24 bit signed power register of the ADC. Power register is the product of current and voltage registers.
Platform: | Size: 11264 | Author: shriram_26 | Hits:

Category

Source Code

Web/Internet

Develop Tools

Document

Other

Search in results

OS

Platform

Language

File Type

Search list

[matlab] Scale-freeInternetsimulation

[Special Effects] 10.1.1.10.6587

[SCM] weigh-scale

[Special Effects] SSR

[matlab] scale_free

[Com Port] the-source-code-of-electronic-scale

[matlab] Solving-scale-free-networks

[matlab] convolution

[Special Effects] Image-gray-scale-transformation

[Software Engineering] 1601.php

[Special Effects] register

[matlab] SCALE-TESTER

[Picture Viewer] scale

[Special Effects] Gray-scale-transformation

[Special Effects] CurvaturePScalePSpace

[Wavelet] scale-edge

[matlab] program-matlab

[Data structs] scale-conversion-2-16

[File Format] Electronic-scale

[Other] weighing-scale-using-SH79F085

CodeBus www.codebus.net