Location:
Search - lpc2378 serial
Search list
Description: 单片机串口通信原理，对于初学者来说是很好的资料。-Single-chip serial communication principle is very good for beginners information.
Platform: |
Size: 56320 |
Author: liujuan |
Hits:
Description: LPC23XX/LPC24XX的串口接收程序。-Serial receive LPC23XX/LPC24XX procedures.
Platform: |
Size: 6144 |
Author: 仝静 |
Hits:
Description: LPC2378关于串口的程序，调试过没有问题的。-LPC2378 on serial procedures, debugging off no problem.
Platform: |
Size: 274432 |
Author: 田有隆 |
Hits:
Description: 开发环境是在MDK 下LPC2378下的UCOS串口编程，和以前那个相比，改动了启动代码，去掉了系统里面的一个报警提示，并且使用了信号量、邮箱等，初学者使用！还没有使用队列，而且要经过改动才能支持串口的多个数据接收目前一次最多是发8个数据。
函数的测试是上电后，P2.0~P2.7从高变低并发一个字母给串口，从低变高，还有一个外部按键中断，按一下，发1000Bytes数据。从串口发的数据给ARM，ARM返回收到的数据。-Development environment is under the LPC2378 under MDK uCOS serial programming, and before that as compared to changes in the startup code, remove the system inside an alarm, and the use of semaphores, mailboxes and so on, for beginners to use! Also did not use the queue, and changes to go through in order to support multiple serial data reception is currently a maximum of eight data fat. Function test is after power, P2.0 ~ P2.7 changed from high to low concurrent serial letter, change from low-high, there is an external interrupt button, click, the 1000Bytes data. Issued from the serial data to the ARM, ARM to return the data received.
Platform: |
Size: 477184 |
Author: 王满仓 |
Hits:
Description: 使用简单:
用 控件->Active=true 打开串口
控件->Read()读, 控件->Write()写.
可以处理控件的事件, 但不是必须的.-Easy to use: Using Controls-> Active = true open the serial port control-> Read () read, controls-> Write () to write. Can deal with the control case, but it is not necessary.
Platform: |
Size: 648192 |
Author: 5445 |
Hits:
Description: This is a Xbee AT DB command reader working on a LPC2378 board, comunicating through the serial. Very simple to understand code. Good to test Xbee range.
Platform: |
Size: 69632 |
Author: fanl |
Hits:
Description: LPC2378 SPI_读写串行NORFlash-LPC2378 SPI_ read and write serial NORFlash
Platform: |
Size: 33792 |
Author: jun |
Hits:
Description: NXP的LPC2378的四个串口的编程，同样对NXP的ARM7的其他系列基本不用修改就可使用。-NXP' s LPC2378 four serial programming, the same pairs of NXP' s ARM7 and other series of the basic no amendment can use.
Platform: |
Size: 295936 |
Author: 萝卜 |
Hits:
Description: ARM7串口程序，芯片为LPC2378，开发环境为KEIL V3.0-ARM7 serial process, chip LPC2378, development environment for the KEIL V3.0
Platform: |
Size: 185344 |
Author: 吕媛媛 |
Hits:
Description: 用于测试LPC2378芯片的串口0的收发数据。-Used for testing the LPC2378 chip serial port 0 of the sending and receiving data.
Platform: |
Size: 352256 |
Author: li |
Hits:
Description: 基于ucos-ii的报警系统的全部源代码，非常适合ucos-ii的初学者，全部用C编写，采用的是ZLG的LPC2378模板，能稳定运行。内容包含串口读写，AT45DB161B SPI接口FLASH读写。GPIO控制等-The alarm system based on uCOS-II full source code, very suitable for beginners of uCOS-II, all prepared with C, using the ZLG LPC2378 template, can stable operation. Contains the serial read and write, read and write FLASH AT45DB161B SPI interface. GPIO control
Platform: |
Size: 1044480 |
Author: chenchen |
Hits:
Description: program for serial transmission inlpc2378. output can be display in lpc2378
Platform: |
Size: 1024 |
Author: prakash R |
Hits:
Description: keil4环境，lpc2378+uCosII平台使用SP2339驱动（串口1扩3）纯净版。编译通过，直接可用-keil4 environment, lpc2378+uCosII platform SP2339 Drive (Serial an extended 3) clean version. Compile, directly available
Platform: |
Size: 1683456 |
Author: 宋亚飞 |
Hits:
Description: LPC2378 串口模块代码。其中包括：UART0；UART1；UART2；UART3.四个片上串行口的控制代码。-LPC2378 serial module code. Including: UART0 UART1 UART2 UART3.
Platform: |
Size: 658432 |
Author: yang |
Hits:
Description: LPC2378 串口程序波特率设定 开发软件ADS1.2-LPC2378 serial port baud rate setting process development software ADS1.2
Platform: |
Size: 139264 |
Author: w_jiawei |
Hits:
Description: NXP MPC2300 I2S 音频demo板演示程序-* This Demo program uses a Keil MPC2300 board with
* an attached I2S Audio demo board. The daughter board
* includes a UDA1341 Audio Chip from NXP Semiconductors.
* The UDA1341 is an economy audio CODEC for portable applications
*
* This demo controls two interfaces on the UDA1341: A control
* interface using the L3 protocol and a data interface using I2S
* The L3 interface uses local IO and timer0 to generate an interrupt
* which creates the protocol
*
* The demo software simply configures the I2S interface within the LPC23xx
*
* The demo takes an analog input signal feed into the UDA1341, the
* UDA1341 digitizes and passes the signal to the LPC2378 through
* the I2S rx port. The demo then loops the signal back to
* the UDA1341 through the tx port.
*
* To run the demo connect a Serial cable to UART port0 at 115,200
* open Hyperterm and explore the menus
*
*/
Platform: |
Size: 119808 |
Author: ck |
Hits: