Description: 802.15.3 无线个域网的仿真模型，基于matlab语言实现-802.15.3 WPAN the simulation model, based on the Matlab language Platform: |
Size: 11364 |
Author:陈飞 |
Hits:
Description: 本程序对rake接收机的仿真程序
在matlab simulink下实现，其信道模型采用802.15.3a信道，信源部分的采用UWB信号，最后通过计算snr与errorbitrate来说明rake接收机性能-this program right rake receiver in the simulation program under Matlab Simulink. its channel model used 802 .15.3 a letter, the source of the signal using UWB, Finally, with errorbitrate snr calculated to illustrate rake receiver performance Platform: |
Size: 25221 |
Author:volvo827 |
Hits:
Description: 802.15.3 无线个域网的仿真模型，基于matlab语言实现-802.15.3 WPAN the simulation model, based on the Matlab language Platform: |
Size: 11264 |
Author:陈飞 |
Hits:
Description: UWB信道仿真程序，基于IEEE802.15.3a，里面有详细地说明。-UWB channel simulation program, based on the IEEE802.15.3a, which has explained in detail. Platform: |
Size: 10240 |
Author:吴杰 |
Hits:
Description: 本程序对rake接收机的仿真程序
在matlab simulink下实现，其信道模型采用802.15.3a信道，信源部分的采用UWB信号，最后通过计算snr与errorbitrate来说明rake接收机性能-this program right rake receiver in the simulation program under Matlab Simulink. its channel model used 802 .15.3 a letter, the source of the signal using UWB, Finally, with errorbitrate snr calculated to illustrate rake receiver performance Platform: |
Size: 24576 |
Author:volvo827 |
Hits:
Description: 解析已封装好的 模拟IEEE 802.3格式的Ethernet帧的封包文件(封包文件是二进制文件，文件名为input，文件中包含若干个Ethernet帧，其中有正确的帧，也有错误的帧)，列出每个Ethernet帧的各个字段的值，并判断帧的正确性。并进行CRC8校验-Analysis has been packaging a good simulation of IEEE 802.3 frame format of Ethernet packets documents (packet file is binary file, the file name is input, the document contains a number of Ethernet frames, including the correct frame, but also the wrong frame), Ethernet frames for each individual field values, and to judge the correctness of the frame. And check CRC8 Platform: |
Size: 100352 |
Author:董巍 |
Hits:
Description: 802.11n physical layer simulink model-802.11n WLAN PHY
Simulation models of 802.11n (modified from 11a PHY model):
wlan/IEEE80211n.mdl
For all simulation models:
--------------------------
Most simulation setting can be configured with the Simulation Settings module
in the lower-left portion of the SIMULINK block diagram. The SNR values to test are
located in the module directly below, PER Test Settings . Currently, the simulation
models are configured for testing a 2x2 antenna configuration, with TGn Channel model D.
For testing with an AWGN channel, the file ch_model.m needs to be modified. For
testing other channel configurations, the file ch_model_tgn.m should be modified (replace
the .mat file tgn_chD_nlos(noflour)_2x2 for load command with other file). Note this file
was generated using the "WLAN MIMO Channel Matlab program" by Laurent Schumacher (see
references [3], [4] below).
Note that most of the other parameters may either be found in the IEEE80211n_settings.m
file, Platform: |
Size: 4047872 |
Author:scootpeng |
Hits:
Description: The scope of the IEEE 802.21 (Media Independent Handover) standard is to ..... The following commands are used to setup UDP agents in simulation scripts: -The scope of the IEEE 802.21 (Media Independent Handover) standard is to ..... The following commands are used to setup UDP agents in simulation scripts: ... Platform: |
Size: 4096 |
Author:dsaasdasdasd |
Hits:
Description: Token Ring local area network (LAN) technology is a communications protocol for local area networks. ... Introduced by IBM in 1984, it was then standardized with protocol IEEE 802.5 and was fairly successful, particularly in corporate environments, but gradually eclipsed by the later versions of Ethernet. Platform: |
Size: 2167808 |
Author:vineeth |
Hits:
Search - 802.3 simulation