Search - stop light

Search - stop light - List

[assembly language] jiaotongdeng DL : 0: 一.设计要求 1.道路有A.B两路,一般情况A.B均有车时,两路各放行10S. 2.红绿灯转换必须经过4秒黄灯闪烁. 3.若两路均无车则保持原状. 4.若一路通行无阻10秒后,另一路无车,则继续放行此路,直到另一路有车. 5.若有紧急车辆通过两路均无红灯4秒,阻止一般车辆通过,让紧急车辆通过6.在数码管显示各路通行的标志和剩余时间. -1. Design requirements 1. Road has two-way AB, AB generally have cars, two of the released 10S. 2. Traffic light conversion must be 4 seconds blinking yellow light. 3. If the two had no car to maintain the status quo. 4. if unimpeded access all the way 10 seconds later, another car-free road, then continue to release this road until the road has another car. 5. if emergency vehicles through two red lights were not four seconds to stop the vehicles passed, so that emergency vehicles through 6. in the digital display various signs and the remainder of the passage of time.
Date : 2025-12-27 Size : 6kb User : 刘智峰
[assembly language] Aexp8-1 DL : 0: Aexp8-1.asm 声-光报警程序 * 运行步骤:1.按下一次开关SW3,开始声-光报警,再按下一次则停止重复上述操作* 2.按下"q"或者"Q",退出-Aexp8-1.asm sound- light alarm procedure* run the steps: 1. Pressing a switch SW3, the beginning of the sound- light alarm, and then press one operation to stop the recurrence of the above* 2. Press the q or Q , exit
Date : 2025-12-27 Size : 1kb User : 李凯
[assembly language] light DL : 0: P1.0端口上接一个发光二极管L1，使L1在不停地一亮一灭，一亮一灭的时间间隔为0.2秒-P1.0 port after another light-emitting diodes L1, so that L1 in non-stop out one bright one, light one out one time interval is 0.2 seconds
Date : 2025-12-27 Size : 65kb User : aaa
[assembly language] weijiyuanli DL : 0: 汇编程序，包括：交通灯控制系统、温度测控系统的设计、电子音乐播放器、键盘电子乐器、电子时钟设计、可任意启动/停止的电子秒表设计-Compilation of procedures, including: traffic light control system, temperature measurement and control system design, electronic music players, electronic musical keyboard, electronic clock design, can be arbitrary start/stop design electronic stopwatch
Date : 2025-12-27 Size : 240kb User : 彷徨
[assembly language] Aexp8-1 DL : 0: 声-光报警程序运行步骤:1.按下一次开关SW3,开始声-光报警,再按下一次则停止重复上述操作* 2.按下"q"或者"Q",退出-this is a sound-light alarm program. Steps:1. push switch3,starting alarm,push switch3 again,it will stop. 2. push Q then quit.
Date : 2025-12-27 Size : 1kb User : cjy
[assembly language] Aexp8 DL : 0: 走马灯（灯光变幻）程序内容：用DIP的8位开关控制走马灯的花样，用SW3控制走马灯的起/停运行步骤:1.按下一次开关SW3,开始灯光变幻,再按下一次则停止可重复进行 * 2.按下SW3后，拨动不同的数码开关DIP,就会出现不同的灯光变幻 * 3.按下"q"或者"Q",退出 -Lantern (lighting changes) program elements: eight with DIP switch control of the pattern lantern, lantern used to control the effect SW3/stop running these steps: 1. Pressing a switch SW3, the beginning of the light changes, and then press the first stop can repeated* 2. SW3 pressed, the Touch different digital switch DIP, there will be changes in different lights* 3. press " q" or " Q" , from the
Date : 2025-12-27 Size : 2kb User : cjy
[assembly language] mcn_sy4 DL : 0: （1）通过开关K0合上与断开控制A/D转换的开始和停止，当开始A/D转换后，每秒对连接到PTB3的模拟量采样一次，结果送指示灯D7~D0显示。（2）采样结果同步通过串行接口发送到PC机（38400bps，N，8，1），显示格式为“The signal is:x.xV”（满量程为5.0V）。 -(1) through the closed switch and disconnect K0 control A/D conversion start and stop, when to start A/D conversion, the second to connect to the analog PTB3 sampling time, the results sent to the indicator light shows that D7 ~ D0. (2) sampling the results of synchronous serial interface is sent to the PC machine (38400bps, N, 8,1), display format for " The signal is: x.xV" (full-scale to 5.0V).
Date : 2025-12-27 Size : 3kb User : aprilgirl
[assembly language] jiaotongdeng DL : 0: 交通灯程序，假设交通灯由直行灯，停止灯，左转灯数码管组成-Traffic light program, assuming the traffic lights straight lights, stop lights, turn left at light digital tubes,
Date : 2025-12-27 Size : 1kb User : lalala
[assembly language] 13826 DL : 0: 实验内容：利用C8051F310单片机设计一个LED灯控制器主要功能和技术指标要求： 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz，1Hz和0.5Hz三种不同频率闪动，各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时，要求采用中断方式 -Experiment: C8051F310 microcontroller design a LED light controller functions and technical requirements: 1. The LED lights external P0.0 end. 2. LED lights press 2Hz flashing 1Hz and 0.5Hz three different frequencies, each continuing 10s. Start and stop flashing LED lights buzzer ringing once. 4 MCU internal timer timing requirements using interrupt
Date : 2025-12-27 Size : 1kb User : 刘王幸
[assembly language] 20105665613826 DL : 0: 实验内容：利用C8051F310单片机设计一个LED灯控制器主要功能和技术指标要求： 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz，1Hz和0.5Hz三种不同频率闪动，各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时，要求采用中断方式 -Experiment: C8051F310 microcontroller design a LED light controller functions and technical requirements: 1. The LED lights external P0.0 end. 2. LED lights press 2Hz flashing 1Hz and 0.5Hz three different frequencies, each continuing 10s. Start and stop flashing LED lights buzzer ringing once. 4 MCU internal timer timing requirements using interrupt
Date : 2025-12-27 Size : 1kb User : 刘王幸
[assembly language] sdjgkdfh-g DL : 0: 实验内容：利用C8051F310单片机设计一个LED灯控制器主要功能和技术指标要求： 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz，1Hz和0.5Hz三种不同频率闪动，各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时，要求采用中断方式 -Experiment: C8051F310 microcontroller design a LED light controller functions and technical requirements: 1. The LED lights external P0.0 end. 2. LED lights press 2Hz flashing 1Hz and 0.5Hz three different frequencies, each continuing 10s. Start and stop flashing LED lights buzzer ringing once. 4 MCU internal timer timing requirements using interrupt
Date : 2025-12-27 Size : 149kb User : 刘王幸
[assembly language] bjkbjkbjkbjkhhjmk DL : 0: 实验内容：利用C8051F310单片机设计一个LED灯控制器主要功能和技术指标要求： 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz，1Hz和0.5Hz三种不同频率闪动，各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时，要求采用中断方式 -Experiment: C8051F310 microcontroller design a LED light controller functions and technical requirements: 1. The LED lights external P0.0 end. 2. LED lights press 2Hz flashing 1Hz and 0.5Hz three different frequencies, each continuing 10s. Start and stop flashing LED lights buzzer ringing once. 4 MCU internal timer timing requirements using interrupt
Date : 2025-12-27 Size : 538kb User : 刘王幸
[assembly language] 2 DL : 0: 实验目的：加深对定时/计数器、中断、IO端口的理解，掌握定时/计数器、中断的应用编程技术及中断程序的调试方法。实验内容：利用C8051F310单片机设计一个LED灯控制器主要功能和技术指标要求： 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz，1Hz和0.5Hz三种不同频率闪动，各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时，要求采用中断方式。提高要求：使用按键（KINT）控制LED灯闪烁模式的切换。 -Experimental purposes: to deepen the timer/counter, interrupt, understanding of the IO port, the master timer/counter, interrupt the application programming techniques and interrupt program debugging. Experiment: C8051F310 microcontroller design a LED light controller functions and technical requirements: 1. The LED lights external P0.0 end. 2. LED lights press 2Hz flashing 1Hz and 0.5Hz three different frequencies, each continuing 10s. Start and stop flashing LED lights buzzer ringing once. 4 MCU internal timer, the interrupt. Improve requirements: Use the buttons (KINT) control LED lights flashing mode switch.
Date : 2025-12-27 Size : 712kb User : 陈定
[assembly language] light DL : 0: 跑马灯作用，可进行双开关控制，k1打开发光二极管一次发光，k2打开发光二极管停止闪烁。-Entertaining diversions, can undertake dual switch control, k1 open leds light at a time, open k2 led to stop blinking.
Date : 2025-12-27 Size : 1kb User : lavender
[assembly language] program DL : 0: 交通灯设计，51单片机汇编编程，有LED灯红绿黄闪烁并有数码管显示倒计时，系统带有可调功能，当东西道上出现紧急情况，可立即调节开关，使东西道调到红灯，停止东西道通行。-Traffic light design, 51 assembly programming, there are red, green and yellow flashing LED lights and a digital display counts down system with adjustable features, when things emergency lane, adjustable switch immediately to make things tract transferred to red light, Road traffic stop things.
Date : 2025-12-27 Size : 11kb User : YD
[assembly language] NEWONEMY DL : 0: 本程序模拟交通灯的基本状态控制，当程序开始工作时，东西南北路口灯均为红色, 持续5s，作为缓冲时间。之后，东西通行，东西绿灯亮25s，南北红灯亮30s，接下来东西紧示，南北继续禁行。之后，南北通行，南北绿灯亮25s，东西红灯亮30s，接下来南北紧示，东西继续禁行。循环往复，实现交通灯的控制。数码管精确显示信号灯持续时间。遇到紧急情况时，按下按钮一，东西方向通行，南北禁行。按下按钮二，南北方向通行，东西禁行。-The basic state of this process simulation traffic light control, when the program starts to work, the north and south, east and west road lights are red, For 5 s, as a buffer time.After that, things, things green light 25 s, north and south turns red, 30 s, the next thing tight, North and south continue to ban.Later, north and south, north and south green light 25 s, something turns red, 30 s, the north and south tight, things continue For stop.Cycling, realize the control of traffic lights.Digital tube precise display lights last time. In case of emergency, press the button a, east-west, north-south ban.Press the button 2, north and south direction, stop.
Date : 2025-12-27 Size : 2kb User : 张扬
[assembly language] Text1 DL : 0: 利用单片机AT89C51控制DS18B20温度传感器对水温控制，当水温低于预设温度值时系统开始加热, 红色发光二极管点亮表示进入热状态，当温度达到预设温度值时自动停止加热,红色发光二极管自动熄灭。预设温度值和实测温度值分别由两个3位数码管显示，范围为0～99℃-Control using SCM AT89C51 DS18B20 temperature sensor temperature control, when the water temperature is lower than the preset temperature value system begins to heat, the red LED lights to indicate the state into the heat when the temperature reaches the preset temperature automatically stop heating, automatic red light-emitting diode extinguished. Preset temperature value and the measured temperature value by two three digital display, the range of 0 ~ 99 ℃
Date : 2025-12-27 Size : 1kb User : yinyu