Search - sort - CodeBus

Search - sort - List

[DSP program] citylujin2 DL : 0: DPS 城市c1到c6间不重复路径按路程总长度从小到大打印输出-DPS city c1 to c6 path between the sort of non-repetition
Date : 2026-01-15 Size : 1kb User : yoyo
[DSP program] VQ_C_language DL : 0: 基于经典LBG算法的矢量量化的C语言实现，注释详尽，很容易让读者理清程序算法和思路。函数的功能和怎么调用，一目了然。-Based on the classic LBG vector quantization algorithm C-language implementation, comment in detail, it is easy for readers to sort out procedural algorithms and ideas. The function and how function calls, at a glance.
Date : 2026-01-15 Size : 3kb User : 陈永恒
[DSP program] F2812_ADsample DL : 0: F2812 AD校正算法，提高转换精度。（CCS3.3开发环境）。 AD采样频率为10K，利用通用定时器T1的周期中断事件来启动AD转换。ADCINA0和ADCINB0为参考电平，实际的电压值分别为0.420和1.653。对ADCINA0、ADCINA1、ADCINB0、ADCINB1四个通道进行连续10次的采样，然后对各个通道的10个采样值进行排序，滤波，最后取平均值。然后由ADCINA0和ADCINB0通道的值计算求得CalGain和CalOffset，最后由这两个量来校正ADCINA1和ADCINB1。-F2812 AD correction algorithm to improve the conversion accuracy. (CCS3.3 development environment). AD sampling rate of 10K, the use of general-purpose timer T1 cycle interrupt event to start the AD conversion. ADCINA0 and ADCINB0 the reference level, the actual voltage values were 0.420 and 1.653. Of ADCINA0, ADCINA1, ADCINB0, ADCINB1 four channel sampling for 10 times, then 10 of each channel samples to sort, filter, and finally averaged. Then ADCINA0 and ADCINB0 channel value obtained CalGain and CalOffset, the last two by the amount of correction ADCINA1 and ADCINB1.
Date : 2026-01-15 Size : 348kb User : 奋斗不止
[DSP program] 2812ADsample DL : 0: AD采样频率为10K，序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器，采样模式采用顺序采样。利用通用定时器T1的周期中断事件来启动AD转换。ADCINA0和ADCINB0为参考电平，实际的电压值分别为0.420和1.653,由于每个板子的具体特性稍有不同，请用万用表自行测量参考电压值。此例程对ADCINA0、ADCINA1、ADCINB0、ADCINB1四个通道进行连续10次的采样，然后对各个通道的10个采样值进行排序，滤波，最后取平均值。然后由ADCINA0和ADCINB0通道的值计算求得CalGain和CalOffset，最后由这两个量来校正ADCINA1和ADCINB1。-AD sampling frequency for the 10K, the sequence generator SEQ1 and SEQ2 cascade into a 16-channel sequencer, sampling mode with sequential sampling. The use of general-purpose timer T1 cycle to start AD conversion interrupt event. ADCINA0, and ADCINB0 as the reference level, the actual voltage values of 0.420 and 1.653, respectively, due to the specific characteristics of each board is slightly different, with a multimeter self-measurement of the reference voltage value. This routine ADCINA0, ADCINA1, ADCINB0, ADCINB1 four channel continuous sampling of 10 times, and then sort the sampled values of the respective channels 10, filtering, and finally take the average. Then to calculated to obtain the CalGain and CalOffset by ADCINA0, and ADCINB0 channel value, the final by these two quantities to to correction ADCINA1 and ADCINB1.
Date : 2026-01-15 Size : 477kb User : pengbin
[DSP program] SORT-F2013 DL : 0: Quick sort algorithm on the F2013. It chooses the splitting value and rearranges the array so that all elements to the left of split value are less than or equal to it and all elements greater that the split value are to the right of it.-Quick sort algorithm on the F2013. It chooses the splitting value and rearranges the array so that all elements to the left of split value are less than or equal to it and all elements greater that the split value are to the right of it.
Date : 2026-01-15 Size : 2kb User : devdev
[DSP program] Digital-signal-processing-code DL : 0: 胡广书数字信号处理第三版源代码，包含所有例程。分章节排序，清晰明了-Hu Guang third edition of the book digital signal processing source code, including all routines. Sub-chapters sort, clarity
Date : 2026-01-15 Size : 2.53mb User : 慎蔚然