Search - LED effect

Search - LED effect - List

[uCOS] ucosii_v200_for_SPCEO61A DL : 0: 此为针对凌阳SPCE061A板进行的uCOS2.00版本的移植，编译通过且运行正常，自带一个LED灯的实验，可以直接看到效果。-This is the board for Sunplus SPCE061A conducted uCOS2.00 version of transplantation, the compiler and run through the normal LED lamp comes with an experiment, you can directly see the effect.
Date : 2026-01-09 Size : 199kb User : Norman Yang
[uCOS] qiangdaqi DL : 0: 这个程序是4路抢答器的程序，这个程序实现的功能是：当主持人按下抢答键后，参赛选手才可以进行抢答。抢答时能发出声响，并通过七段数码管显示是哪位选手抢答的。这个程序在PIC单片机上测试过，效果良好-This program is 4-way Responder program, this program is to achieve the function: When the host pressed to answer in key, players can only answer in. Responder when audible, and through the seven-segment LED display which player is the answer in the. This program is tested on PIC microcontrollers, to good effect
Date : 2026-01-09 Size : 1kb User : 蔡坤堤
[uCOS] ucos--led DL : 0: 基于STM32_V3.4固件函数库的uCOSII实例，在MDK4.12中编译通过，入门程序，实现跑马灯效果。-Based on STM32_V3.4 firmware function library uCOSII instance, compiled by the MDK4.12, entry procedures, to achieve Marquee effect.
Date : 2026-01-09 Size : 6.16mb User : jeson shen
[uCOS] Desktop DL : 0: 功能：读取按键,控制LED闪烁。首先对引脚选择寄存器PINSEL赋值为0，设置引脚连接GPIO。,然后对按键进行扫描，等到有键按下时，开始LED闪烁的程序。为了使LED有各种各样的闪烁结果，对其设计了一个表LED_TBL[]，并不断调用，对P0[7:0]这8个设置为输出的I/O口进行置一或清零，得到花样流水灯的效果。当接P0.14的按键按下时，LED闪烁状态会回到最初全灭至亮状态，然后继续按照其他花式闪烁。 -Function: Reads keys, control LED flashes. First register PINSEL pin assignment to 0, set the pin connections GPIO. And then scan button, wait until a key is pressed, the program began flashing LED. In order to make a wide variety of LED flashing result, its design a table LED_TBL [], and continue to call for P0 [7: 0] This 8 is set to output an I/O port for a set or cleared get water lights pattern effect. When the button is pressed pick P0.14, LED flashing light will return to the original state all off, and then continue to follow the other fancy flashing.
Date : 2026-01-09 Size : 71kb User : 范鹏
[uCOS] STM32F103C8T6_UCOS_DEMO DL : 0: 这是按照前面我发的从零开始学习ucosii手册，编写成功的模板。芯片是stm32f103c8t6，移植在f103芯片上，都是同理可得。记住虽然可以直接拿着用，但是要修改对应的IO口哦，程序效果是led小灯闪烁。（有一个问题我也不太清楚，理论上c8t6的启动文件应该是startup_stm32f10x_md.s，但是用它却不能成功。用startup_stm32f10x_hd.s却成功了。）(This is a successful template written in front of the uCOSII manual that I started from zero. The chip is stm32f103c8t6, and the transplant is on the F103 chip. Remember that although it can be used directly, but to modify the corresponding IO mouth Oh, the program effect is the LED light flicker. (there is one problem I'm not very clear about. In theory, c8t6's startup file should be startup_stm32f10x_md.s, but it can't be successful with it. It was successful with startup_stm32f10x_hd.s.))
Date : 2026-01-09 Size : 977kb User : 悲天名人