Search - shell - CodeBus

Search - shell - List

[ARM-PowerPC-ColdFire-MIPS] UEFI Shell Specification_2_0.pdf DL : 0: Date : 2010-12-07 Size : 536.32kb User : vastwen@163.com
[ARM-PowerPC-ColdFire-MIPS] shell-HHAT91rm9200 DL : 0: shell-HHARM9200.rar 华恒 AT91rm9200 中Busybox shell的源代码-shell-HHAT91rm9200.rar, this is the source code of the Busybox shell under HUAHENG AT91rm9200 platform.
Date : 2025-12-22 Size : 152kb User : 张晓东
[ARM-PowerPC-ColdFire-MIPS] 汇编语言的SHELL DL : 0: 一个让你忘不了的回忆,这个东西会让你再次重温当年写程序的-let you forget one's memory, this one will allow you to review again the procedure was then
Date : 2025-12-22 Size : 4kb User : 周禄均
[ARM-PowerPC-ColdFire-MIPS] shell DL : 0: shell驱动－－－基于MIPS平台，M4K，yamon-shell based on the MIPS platform driver---, M4K, yamon
Date : 2025-12-22 Size : 5kb User : alterli
[ARM-PowerPC-ColdFire-MIPS] MCF5275SC DL : 0: COLDFIRE 5275板极初始化程序，完成CPU的寄存器、中断、RAM的初始化，并有个SHELL -COLDFIRE 5275 board-level initialization procedures, completion of CPU registers, interrupt, RAM initialization, and there is a SHELL
Date : 2025-12-22 Size : 682kb User : anthens
[ARM-PowerPC-ColdFire-MIPS] command DL : 0: 一个类似于shell的程序，在s3c44b0上实现串口0输入相应命令后cpu执行相关功能。-one shell based on s3c44b0
Date : 2025-12-22 Size : 35kb User : eric
[ARM-PowerPC-ColdFire-MIPS] res.tar DL : 0: 《ARM嵌入式系统实验教程》P313面最后一段，要求将 /usr/local/lib/minigui/res/* 下所有文件都拷贝到开发板的/usr/local/lib/minigui/res 文件夹下。但是由于在 uclinux下只支持 cp srcname destname 格式，且不支持 -a 选项（实际上是任何选项都不支持），所以不能拷贝目录，也不能删除目录（痛苦啊）。而这里要拷贝的res文件夹下的内容很多，逐个写指令来拷贝不太现实，于是我做了一个shell帮助执行这些指令。打开下面这个压缩包（拷贝到linux下然后解压） F:\MyInfo3\MySource\Linux\SmartARM2200实验学习\MiniGUI\6.1 MiniGUI for uclinux \res.tar.gz 在res文件夹下还有一个叫res的文件夹，将这个文件夹拷贝到/home/armwork 目录下，再将res文件夹下的cpres文件拷贝到实验板上，使用命令 ./cpres 执行该shell文件即可完成拷贝任务。-"ARM Embedded System Experimental Course" P313 side last paragraph of the request/usr/local/lib/minigui/res /*, all files are copied to the development board of the/usr/local/lib/minigui/res folder. However, because under the uclinux support cp srcname destname format only, and do not support the-a option (in fact do not support any options), it can not copy the catalog, can not remove directory (pain ah). And here s res folder to copy the contents under a lot of written instructions to copy one by one is not realistic, so I had a shell to help implement these instructions. This opens the following archive (copy under linux and then extract) F: \ MyInfo3 \ MySource \ Linux \ SmartARM2200 experimental study \ MiniGUI \ 6.1 MiniGUI for uclinux \ res.tar.gz In the res folder and a folder called res, copy this folder to/home/armwork directory Then the cpres res folder files are copied to experiment board, use the command./Cpres to complete the implementation of the she
Date : 2025-12-22 Size : 486kb User : jerry
[ARM-PowerPC-ColdFire-MIPS] STM32F107shell DL : 0: stm32F107综合测试程序包含shell USB uIP CAN 内部Flash DS18B20 IO-stm32F107 comprehensive test program consists of a shell USB uIP CAN internal Flash DS18B20 IO, etc.
Date : 2025-12-22 Size : 1.01mb User : keyin
[ARM-PowerPC-ColdFire-MIPS] porus-0.1.1 DL : 0: PORUS is a portable USB device stack. It is designed to contain, as far as possible, all of the code common to a complete USB device implementation. PORUS is neither stable nor finished. Until version 1.0.0, the API may change, perhaps significantly. At this time, only one port is available. It has been tested on the MMB0 DSP board, which uses the Texas Instruments TMS320VC5507 DSP. More ports are planned. Installation ------------ PORUS consists of source files and a program called usbgen. There is no installation procedure for the source files these are meant to be copied directly to each project. To install usbgen, you need Python and a shell environment on Windows, cygwin is highly recommended (www.cygwin.com). Installation is as follows: Change to the usbgen directory, Run python setup.py install (on Linux, you need to be root)-PORUS is a portable USB device stack. It is designed to contain, as far as possible, all of the code common to a complete USB device implementation. PORUS is neither stable nor finished. Until version 1.0.0, the API may change, perhaps significantly. At this time, only one port is available. It has been tested on the MMB0 DSP board, which uses the Texas Instruments TMS320VC5507 DSP. More ports are planned. Installation ------------ PORUS consists of source files and a program called usbgen. There is no installation procedure for the source files these are meant to be copied directly to each project. To install usbgen, you need Python and a shell environment on Windows, cygwin is highly recommended (www.cygwin.com). Installation is as follows: Change to the usbgen directory, Run python setup.py install (on Linux, you need to be root)
Date : 2025-12-22 Size : 230kb User : karamba