Search - interrupt timer routine

Search - interrupt timer routine - List

[ARM-PowerPC-ColdFire-MIPS] S3C4510B_Timer DL : 0: 学习ARM中断最好的例程，采用C语言方式设置中断向量。-Best routine for ARM interrupt learning, using C language to set up interrupt vector.
Date : 2026-01-22 Size : 77kb User : Dayspring
[ARM-PowerPC-ColdFire-MIPS] 2812adc_eva DL : 0: 本人在调试步进电机项目中用来调试2812片内adc的代码，eva启动，定时器1周期中断，包含寄存器初始化和中断服务程序代码，两个通道采样，可以正常进入中断并完成采样，花了1周时间调通的-Stepper motor I debug the project in 2812 for debugging adc code, eva start a cycle timer interrupt, including the register initialization code and interrupt service routine, the two-channel sampling, can interrupt the normal access to and completion of sampling spent 1 week' s time to tune
Date : 2026-01-22 Size : 264kb User : 常迪
[ARM-PowerPC-ColdFire-MIPS] TIMER_RVMDK DL : 0: 本源码为STM32的定时器使用例程,主要测试定时器2的功能。开发环境realviewMDK 将定时器2设置为输出比较模式，4个通道分别设置不同的比较值，因此每个通道产生中断的频率不同。在中断处理程序中分别相应的LED翻转，从而可以观察到4个闪烁频率不同的LED。闪烁频率由快到慢：LD5、LD6、LD4、LD3。-The source code for the STM32 timer routine use, the main test Timer 2 functions. Development environment realviewMDK set the timer 2 output compare mode, four-channel comparison of each set different values, so generate an interrupt for each channel a different frequency. In the interrupt handler, respectively, the corresponding LED flip, which can be observed four different frequencies of flashing LED. Flicker frequency by approaching slowly: LD5, LD6, LD4, LD3.
Date : 2026-01-22 Size : 148kb User : huangshengqun
[ARM-PowerPC-ColdFire-MIPS] TIMER_INT DL : 0: LPC2103ARM7例程，定时器中断方式。-LPC2103ARM7 routine, the timer interrupt.
Date : 2026-01-22 Size : 91kb User : snow
[ARM-PowerPC-ColdFire-MIPS] STM32F0XX教程+例程源码 DL : 0: STM32F0XX教程+例程源码教程目录：工程篇：搭建KEIL-MDK开发平台及制作MDK工程文件模板.pdf 资料篇-NUCLEO-072RB开发板特性讲解及资料准备.pdf 初级教程篇：按键(中断方式)实现24C04存储器内容读写.pdf 初级教程篇：实现一个LED灯(软件延时 systick定时器).pdf 中级教程篇：利用SPI总线构建NUCLEO-072RB和NUCLEO-302RB双机处理系统.pdf 中级教程篇：利用定时器实现6路互补PWM波形输出.pdf 高级教程篇：基于Labview上位机界面的NUCLEO-072RB数据采集系统.pdf 例程目录： 1.ADC 2.BLDC 3.DEMO-工程模板 4.EEPROM 5.KEY(中断方式) 6.KEY-EEPROM 7.LED（systick定时） 8.LED(软件延时) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART(printf 查询方式接收) 14.UART(中断方式方式接收)(STM32F0XX tutorial + routine source code Directory of courses: Project: building KEIL-MDK development platform and making MDK project document template.Pdf Information sheet -NUCLEO-072RB development board characteristics and data preparation.Pdf Primary tutorial: key (interrupt mode) to achieve 24C04 memory content read and write.Pdf Junior tutorial: realizing a LED lamp (software delay systick timer).Pdf Intermediate tutorial: using SPI bus to build NUCLEO-072RB and NUCLEO-302RB dual processor system.Pdf Intermediate tutorial: using timer to realize 6 complementary PWM waveform output.Pdf Advanced tutorial: NUCLEO-072RB data acquisition system based on Labview host computer interface.Pdf Routine Directory: 1.ADC 2.BLDC 3.DEMO- engineering template 4.EEPROM 5.KEY (interrupt mode) 6.KEY-EEPROM 7.LED (systick timing) 8.LED (software delay) 9.PWM 10.SPI-MASTER-F0 11.SPI-SLAVE-F3 12.STM32-Labview-ADC 13.UART (printf query mode) 14.UART (interrupt mode receive))
Date : 2026-01-22 Size : 19.73mb User : Putty