Search - interrupt timer routine

Search - interrupt timer routine - List

[Embeded-SCM Develop] TMSX28xx DL : 0: X28xx功能单元使用.doc 例1、初始化锁相环及外设时钟函数例2、.cmd格式文件举例例3、定时器中断应用举例例4、利用事件管理器输出多种频率的正弦信号输出例程例5、SPI和DAC TLV 5617接口例程例6、CAN总线消息发送例程例7、使用FIFO缓冲发送数据例8、使用FIFO缓冲接收数据例9、ADC应用举例 -Functional unit X28xx use. Doc Cases 1, phase-locked loop initialization and peripheral clock function cases 2,. Cmd files, for example cases of 3, timer 4 interrupt application cases, for example, using a variety of event management output frequency sinusoidal signal output routine cases 5, SPI interface DAC TLV 5617 and routine cases 6, CAN bus messages routine cases of 7, using FIFO buffer to send data of 8 cases, the use of cases receive data FIFO buffer 9, ADC application example
Date : 2026-01-22 Size : 32kb User : haoz
[Embeded-SCM Develop] 5.TimerInterrupts DL : 0: zigbee cc2430模块定时器中断，中断的产生和中断服务程序的用法-zigbee cc2430 module timer interrupt, interrupt generation and interrupt service routine use of
Date : 2026-01-22 Size : 71kb User : 莫为
[Embeded-SCM Develop] ADSample DL : 0: 本程序是通过AD校正来提高2812 AD采样的精度，AD采样频率为10K，序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器，采样模式采用顺序采样。利用通用定时器T1的周期中断事件来启动AD转换。 ADCINA0和ADCINB0为参考电平，实际的电压值分别为0.420和1.653,此例程对 ADCINA0、ADCINA1、ADCINB0、ADCINB1四个通道进行连续10次的采样，然后对各个通道的10个采样值进行排序，滤波，最后取平均值。然后由ADCINA0 和ADCINB0通道的值计算求得CalGain和CalOffset，最后由这两个量来校正 ADCINA1和ADCINB1。-The correct procedure is to increase by AD 2812 AD sampling precision, AD sampling frequency of 10K, and SEQ2 SEQ1 cascaded sequencer as a 16-channel sequencer, sampling mode using sequential sampling. T1 using the universal periodic interrupt timer event to start the AD conversion. ADCINA0 and ADCINB0 for the reference level, the actual voltage values were 0.420 and 1.653, this routine of ADCINA0, ADCINA1, ADCINB0, ADCINB1 four channel sampling for 10 times, and then 10 of each channel to sort the samples , filter, and finally averaged. Then ADCINA0 and ADCINB0 channel value obtained CalGain and CalOffset, the final amount of correction by the two ADCINA1 and ADCINB1.
Date : 2026-01-22 Size : 103kb User : 张良
[Embeded-SCM Develop] C51EX DL : 0: 单片机配套例程60个，关于STC51，定时器，中断，数码管，LED等应用-SCM supporting routine 60, about STC51, timer, interrupt, digital tube, LED application, etc
Date : 2026-01-22 Size : 28.04mb User : 1313
[Embeded-SCM Develop] mpc8641timer DL : 0: mpc8640d定时器的驱动，包含寄存器的配置和中断服务函数。-mpc8640d timer drive that contains the configuration register and the interrupt service routine.
Date : 2026-01-22 Size : 4kb User : wu
[Embeded-SCM Develop] EFM8BB2_ADC DL : 0: ADC实例，用于模拟量采样实例，内部REF(The system is clocked by the internal 24.5 MHz oscillator divided by 1. // Timer 2 triggers a conversion on ADC0 on each overflow. The completion of // this conversionin turn triggers an interrupt service routine (ISR). The ISR // averages 2048 measurements, then prints the value to the terminal via printf // before starting another average cycle. // // The analog multiplexer selects P1.7 (ADC0.15) as the positive ADC0 input. // This pin is configured as an analog input in the port initialization // routine. The negative ADC0 input is connected via mux to ground, which // provides for a single-ended ADC input.)
Date : 2026-01-22 Size : 7kb User : Redcell