Description: 用于串口调试的工具----串口精灵,不用安装的绿色软件-for serial debugging tools---- Serial genies, do you need to install the software green Platform: |
Size: 282624 |
Author:wuqj |
Hits:
Description: 监控程序（Monitor）的主要功能是对应用系统硬件及底层软件进行调试，也称为Debug程序，是最基本的调试工具。MC9S12DG128的Flash有128K，RAM有8K，而监控程序源代码占用不到3K FLASH，占用23字节RAM。这对用户程序的空间影响并不大。异步串行口是要用来做与PC通讯服务的，监控程序可以用，应用程序当然也可以使用。 -Monitoring Program (Monitor) of the main functions of the system on the application of the underlying hardware and software debugging, also known as Debug procedures, is the most basic debug tools. Flash has MC9S12DG128 the 128K, RAM has 8K, while the monitoring program source code occupy less than 3K FLASH, occupy 23 bytes RAM. This user program space is not too great. Asynchronous serial port is used to do with the PC communication services, monitoring procedures can be used, the application of course, can also be used. Platform: |
Size: 8192 |
Author:ttjj120 |
Hits:
Description: 程序已经过仿真软件的调试，可以直接下载使用，程序是基于盛群公司和太芯片的程序编写和开发，有助于新手之间的交流学习。文档中包括中断程序的调试，串口原程序的编写，以及点阵和蜂鸣器能单片机外部设备的应用-Program has been simulation software debugging, you can directly download the program is based on the Holtek chip companies and programming and too developed to help communication between novice learning. Documents, including interrupt debugging, serial original procedures for the preparation and dot matrix and buzzer to the application of single-chip peripherals Platform: |
Size: 4213760 |
Author:clliff hawk |
Hits:
Description: 串口调试助手，源程序实在太大了，分了三个上传上来，解压后把后两个文件夹中的文件发到第一个文件夹就行了-Serial debugging assistant, the source is too great, divided into three uploaded onto unpacked after two folders in the file is sent to the first folder on the line Platform: |
Size: 14669824 |
Author:shandun |
Hits:
Description: 串口调试助手，源程序实在太大了，分了三个上传上来，解压后把后两个文件夹中的文件发到第一个文件夹就行了-Serial debugging assistant, the source is too great, divided into three uploaded onto unpacked after two folders in the file is sent to the first folder on the line Platform: |
Size: 25477120 |
Author:shandun |
Hits:
Description: 串口调试助手，源程序实在太大了，分了三个上传上来，解压后把后两个文件夹中的文件发到第一个文件夹就行了-Serial debugging assistant, the source is too great, divided into three uploaded onto unpacked after two folders in the file is sent to the first folder on the line Platform: |
Size: 12302336 |
Author:shandun |
Hits:
Description: 单片机虚拟串口仿真图，里面有虚拟串口软件和串口调试助手，还有用proteus进行的仿真图，不用开发板一样进行仿真，只能说proteus太强大了。只要你想不到的，没有他做不到的！-Virtual serial port emulation chip chart, which has a virtual serial port software and serial debugging assistant, as well as performed with proteus simulation map, not the same simulation development board can only say proteus too strong. As long as you think, no he can not do! Platform: |
Size: 5294080 |
Author:杨刚 |
Hits:
Description: 1、该例程为STM32串口1测试例程。
2、使用说明
(1)工程文件路径：.\USER\STM32-DEMO.uvprojj。
(2)请使用MDK 4.0以上版本打开,MDK版本过低会导致无法识别工程。
(3)下载调试工具为JLINK。
(4)请将串口线(两头皆为母的交叉串口线)插在板子COM1口上,并打开超级终端或串口助手，配置波特率115200，8位，一个停止位，无校验位。
(5)插上DC-5V电源、插上JLINKV8后，点击MDK工具栏中的LOAD按钮即可下载程序。-1, the routine test routines for the serial one. 2, the use of (a) the project file path:. \ USER \ STM32-DEMO.uvprojj. (2) Please use the MDK 4.0 or later to open, MDK version is too low can cause unrecognized works. (3) download debugging tools JLINK. (4) connect the serial cable (two are female crossover serial cable) plugged into the COM1 port on the board, and open HyperTerminal or serial assistant, configure the baud rate 115200 bits, one stop bit, no parity. (5) Plug DC-5V power supply, plug JLINKV8, click on the toolbar MDK LOAD button to download the program. Platform: |
Size: 2349056 |
Author:wefj |
Hits:
Description: 1、该例程为I2C例程。
2、使用说明
(1)工程文件路径：例程目录\I2C\MDK-ARM\Project.uvproj。
(2)请使用MDK 4.0以上版本打开,MDK版本过低会导致无法识别工程。
(3)下载调试工具为ULINK。
(4)请将JP1插1-2位置。
(5)请将串口线(直连串口线)插在板子COM1口上,并打开超级终端或串口助手，配置波特率115200，8位，一个停止位，无校验位。
(6)HEX文件下载到板子后,使用超级终端或串口调试助手可以看到调试信息,表明例程运行正确。-1, the routine for the I2C routines. 2, the use of (1) the project file path: routine directory \ I2C \ MDK-ARM \ Project.uvproj. (2) Please use the MDK 4.0 or later to open, MDK version is too low will lead to the identification project. (3) Download debugging tools ULINK. (4) Please insert JP1 1-2 position. (5) set the serial cable (direct serial cable) plugged into the board COM1 port and open HyperTerminal or serial assistant, configure the baud rate 115200 bits, one stop bit, no parity. (6) HEX file is downloaded to the board, use HyperTerminal or serial debugging assistant can see the debug message that routine run correctly. Platform: |
Size: 905216 |
Author:gmx |
Hits:
Search - serial debugging too