Description: 本设计采用凌阳16 位单片机SPCE061A对步00进电机进行控制，通过IO口输出的具有时序的方波作为步进电机的控制信号，信号经过芯片L298N驱动步进电机；-This design uses 16-bit single-chip Sunplus SPCE061A to step into the motor control 00, through the IO port with the output timing of the square wave as a stepper motor control signal, the signal after the chip stepper motor driver L298N Platform: |
Size: 327680 |
Author:王忠 |
Hits:
Description: 本设计采用凌阳16 位单片机SPCE061A对步进电机进行控制，通过IO口输出的具有时序的方波作为步进电机的控制信号，信号经过芯片L298N驱动步进电机-This design uses SPCE061A Sunplus 16-bit single-chip control of the stepper motor, through the IO port with the output timing of the square wave as a stepper motor control signal, the signal after the chip stepper motor driver L298N Platform: |
Size: 348160 |
Author:缪中历 |
Hits:
Description: 基于L297和L298N的步进电机驱动电路，可直接驱动步进电机-Based on the L297 and L298N driver circuit of the stepper motor can directly drive stepper motor Platform: |
Size: 51200 |
Author:朱惠彬 |
Hits:
Description: 利用mega128控制由L298和L297构成的驱动板，驱动步进电机-Mega128 control using L298 and L297-driven composition of boards, stepper motor driver Platform: |
Size: 52224 |
Author:李文 |
Hits:
Description: 两线步进电机驱动芯片L297说明，中文资料，与L298配套使用来驱动步进电机
步进电机\L297.rar-Two lines L297 stepper motor driver chip that the Chinese data, and supporting the use of L298 to drive the stepper motor Platform: |
Size: 142336 |
Author:lee |
Hits:
Description: 此为09年电子设计大赛的电机驱动程序，电机为步进电机，驱动为L298和nec的控制芯片组成-This is the 2009 Electronic Design Contest of the motor drive, motor for the stepper motor, driver for the L298 and the control chips nec Platform: |
Size: 607232 |
Author:zz |
Hits:
Description: 采用L298芯片做成步进电机驱动电路。最大电流可以输出2A。-Made by L298 chip stepper motor driver circuit. Maximum current to the output 2A. Platform: |
Size: 7168 |
Author:邓志远 |
Hits:
Description: 本驱动程序主要针对L298驱动的步进电机，用MSP430单片机编写，在自动控制设计中应用广泛，且有较好的驱动功率。-The main driver for the L298 stepper motor driven, with the MSP430 microcontroller is written in the automatic control design is widely used, and there is a better drive power. Platform: |
Size: 17408 |
Author:易金桥 |
Hits:
Description: 仅仅使用L298驱动芯片，主控为51单片机，在keil中调试测过，专门驱动步进电机的！不是直流电机。-Just use the L298 driver chip, the master microcontroller 51, in keil debugging measured before, specifically to drive stepper motor! Not a DC motor. Platform: |
Size: 12288 |
Author:陈泉 |
Hits:
Description: 51单片机通过L297和L298控制步进电机驱动程序-51 MCU through the control of L297 and L298 stepper motor driver Platform: |
Size: 1024 |
Author:pengli |
Hits:
Description: l298，l297步进电机驱动模块程序，用来说明模块的使用方法，以及步进电机的控制原理-l298, l297 stepper motor driver module used to describe the use of the module, as well as stepper motor control principles Platform: |
Size: 3563520 |
Author:王韬 |
Hits:
Description: 自动光控窗帘毕业设计，使用51单片机控制，1602显示，包含时钟模块，l298和l297步进电机驱动。有电路图，源代码，仿真电路和论文-Automatic light control curtains graduated from the design, the use of SCM 51, 1602, contains the clock module, l298 and l297 stepper motor driver. Schematics, source code, simulation circuit and papers Platform: |
Size: 9480192 |
Author:胡强 |
Hits:
Search - l298 stepper driver